Crosby City Zoning Code
MANUFACTURED HOMES
LAND USE CLASSIFICATIONS AND DEFINITIONS
§ 154.315 PURPOSE.
The purpose of this amendment is to add provisions for manufactured homes in Residential Zoning Districts.
(Prior Code, § 13.88)
§ 154.316 SPECIAL LAND USE PROVISIONS.
Allow dwelling, manufactured housing in the R-1 and R-2 Zoning Districts as a permitted use as follows.
Use | R-1 SF | R-2 MF | R-3 Man. | B-1 CBD | B-2 High | I Ind | P Pu |
Dwelling, manufactured housing | P | P | C | ||||
C - denotes conditionally permitted use P - denotes permitted use Blank - denotes prohibited use | |||||||
(Prior Code, § 13.89)
§ 154.317 AUTHORIZED PLACEMENT.
The city authorizes the placement of manufactured homes in residential zones within the city if such manufactured homes comply with the following conditions.
(A) Manufactured homes shall comply with all zoning regulations for the zone in which they are located.
(B) A building permit and any other required permits shall be obtained for manufactured homes.
(C) No manufactured home located within an area platted after 1950 or located within an R-1 Zoning District shall have a building width of less than 24 feet at its narrowest point.
(D) No manufactured home located within an area platted before 1950 or located within an R-2 Zoning District shall have a building width of less than 24 feet at its narrowest point.
(E) Additionally, as to foundations, the following shall apply:
(1) Manufactured homes shall be placed on permanent foundations;
(2) Consisting of a cement slab or cement exterior foundations walls;
(3) Which otherwise comply with the Uniform Building Code (as between this chapter and the Uniform Building Code, the more restrictive shall apply);
(4) Which are solid for the complete perimeter of the house;
(5) Consist of stone or block with wet joint mortar or interlocking blocks;
(6) Plans and specifications must be those supplied by the manufacturer of the home; and
(7) Must be submitted to the city for approval prior to commencing construction.
(F) As to roofs, manufactured homes shall have a roof which is:
(1) Manufacturer-engineered;
(2) Manufacturer-approved;
(3) Pitched; and
(4) Have eaves of not less than six inches.
(G) Manufactured homes shall have a minimum floor area of 720 square feet.
(H) All hitches and wheels must be removed.
(Prior Code, § 13.90) (Ord. 2013-4, passed 11-12-2013)
§ 154.318 BUILDING WIDTH.
The smallest horizontal dimension of the major portion of a dwelling which does not include decks or patios.
(Prior Code, § 13.91)
§ 154.319 PLACEMENT IN RESIDENTIAL ZONES.
The city authorizes the placement of manufactured houses in residential zones within the city if such manufactured houses comply with the following conditions.
(A) Such houses shall comply with all zoning regulations for the zone in which they are located.
(B) A building permit and any other required permits shall be obtained for such manufactured housing.
(C) No such house located within an area platted after 1950 shall have a width of less than 20 feet at its narrowest point.
(D) No such house located on land platted previous to 1950 shall have a width of less than 20 feet at its narrowest point.
(E) Such houses shall be placed on permanent foundations which comply with the uniform building code as adopted in the state and which are solid for the complete circumference of the house.
(F) Any such manufactured house shall have exterior siding extending from within six inches of the dirt or two inches of concrete, which siding shall be of a conventional exterior dwelling-type material.
(G) Any such manufactured house shall have a pitched roof covered with shingles or tile and have eaves of not less than six inches.
(H) All such manufactured houses shall be built in compliance with M.S. §§ 327.31 to 327.35, as they may be amended from time to time.
(Prior Code, § 13.96)