Moreno Valley City Zoning Code

CHAPTER 9

03 RESIDENTIAL DISTRICTS

§ 9.03.010 Purpose and intent.

The general plan outlines goals, objectives, and policies regarding the character of residential uses and developments. It is the purpose of this chapter to provide regulations that implement those goals, objectives and policies toward the provision of a wide range of residential opportunities and dwelling unit types that meet the needs of present and future Moreno Valley residents of all socioeconomic groups. It is the further intent of this chapter to: ensure adequate light, air, privacy and open space for each dwelling; to minimize traffic congestion and to avoid the overloading of utilities by preventing the construction of buildings of excessive bulk or number in relation to the land area around them; to protect residential properties from objectionable noise, illumination, unsightliness, odors, smoke and other influences; and to facilitate the provision of utility services and other public facilities commensurate with anticipated population, dwelling unit densities, and service requirements.

(Ord. 359, 1992)

§ 9.03.020 Residential development districts.

The following subsections describe the general product type and density provisions for the specified residential development districts. The ultimate density allowed in any residential district shall be determined through the project review process and public hearings as described in Chapter 9.02 of this title. The planning commission and city council shall have the authority to reasonably condition any discretionary residential development to ensure proper transition and compatibility to adjacent developments, existing or proposed.

Rural Residential District (RR). In conformance with the purpose and intent of the rural residential land use designation established in the city's general plan, it is the intent of the rural residential district to provide for and protect rural lifestyles involving large lots growing fruits and vegetables, and animal keeping. It is the further intent of this district to protect natural resources and hillsides in the rural portions of the city.

Hillside Residential District (HR). The primary purpose of the hillside residential (HR) district is to balance the preservation of hillside areas with the development of view oriented residential uses. It is the further intent of this district to provide regulations for the limited development of those hillside areas in a manner that will maintain natural open space areas, protect significant landforms and other natural resources, protect views from existing development, retain opportunities for views from development sites, preserve and enhance vistas from public places, minimize the extent and occurrence of erosion and other potential hazards of development in areas of steep topography, and generally protect the public health, safety and welfare. The keeping of animals is permitted, however, the keeping of large animals may be prohibited subject to compatibility with local urbanization and topographic constraints.

Residential 1 District (R1). The primary purpose of the R1 district is to provide for and protect the rural and agricultural atmosphere, including the keeping of animals, that have historically characterized these areas. This district is intended as an area for development of low density, large lot, single-family residential dwelling units at a maximum density of one dwelling unit (DU) per net acre.

Residential 2 District (R2). The primary purpose of the R2 district is to provide for suburban life-styles on residential lots larger than are commonly available in suburban subdivisions, and to allow nonequestrian residential developments in a rural atmosphere. This district is intended as an area for development of large lot, single-family residential development at a maximum allowable density of two DUs per net acre.

Residential Agriculture 2 District (RA2). The primary purpose of the RA2 district is to provide for suburban life-styles on residential lots larger than are commonly available in suburban subdivisions and to provide for and protect the rural and agricultural atmosphere, including the keeping of animals, that have historically characterized these areas. This district is intended as an area for development of large lot, single-family residential development at a maximum allowable density of two dwelling units (DU) per net acre.

Residential 3 District (R3). The primary purpose of the R3 district is to provide a transition between rural and urban density development areas, and to provide for a suburban life-style on residential lots larger than those commonly found in suburban subdivisions. This district is intended as an area for development of large lot, single-family residences at a maximum allowable density of three DUs per net acre.

Residential 5 District (R5). The primary purpose of the R5 district is to provide for residential development on common sized suburban lots. This district is intended as an area for development of single-family residential and mobile home subdivisions at a maximum allowable density of five DUs per net acre in accordance with the provisions outlined herein.

Residential 10 District (R10). The primary purpose of the R10 district is to provide for a variety of residential products and to encourage innovation in housing types with enhanced amenities such as common open space and recreation areas. This district is intended as an area for development of attached residential dwelling units, as well as mobile home parks at a maximum allowable density of 10 dwelling units per net acre in accordance with the provisions outlined herein.

Residential Single-Family 10 District (RS10). The primary purpose of the RS10 district is to provide for residential development on small single-family lots with amenities not generally found in suburban subdivisions. The district is intended for subdivisions at a maximum allowable density of 10 dwelling units per net acre.

Residential 15 District (R15). The primary purpose of the R15 district is to provide a broadened range of housing types for those not desiring detached dwellings on individual parcels, and with open space and recreational amenities not generally associated with typical suburban subdivisions. This district is intended as an area for development of attached residential dwelling units, as well as mobilehome parks, at a maximum allowable density of 15 DUs per net acre in accordance with the provisions outlined herein.

Residential 20 District (R20). The primary purpose of the R20 district is to provide a broadened range of housing types in a more urban setting than is typically found within other areas of the city. This district is intended as an area for development of multifamily residential dwelling units, as well as mobilehome parks, at a maximum allowable density of 20 DUs per net acre in accordance with the provisions outlined herein.

Residential 30 District (R30). The primary purpose of the R30 district is to provide a broadened range of housing types in an urban setting than is typically found within other areas of the city. This district is intended as an area for development of multifamily residential dwelling units at a maximum allowable density of 30 DUs per net acre in accordance with the provisions outlined herein.

(Ord. 359, 1992; Ord. 468 § 1.3, 1995; Ord. 547 § 1.1, 1999; Ord. 726 § 4.2, 2006; Ord. 797 § 2.2, 2009)

§ 9.03.030 Use regulations for residential districts.

For residential districts, unless otherwise expressly provided in this title, permitted uses are limited to those described in the Permitted Uses Table, Section 9.02.020 of this title. All permitted nonresidential uses shall comply with all commercial standards of the development code.

(Ord. 359, 1992; Ord. 520 § 1.8, 1997)

§ 9.03.040 Residential site development standards.

The following standards shall apply to land and permitted or conditionally permitted buildings and structures located within the herein described residential districts. The standards stated herein are not intended to prevent more restrictive private site development standards contained in the covenants, conditions and restrictions or other private consensual restrictions imposed on any property or dwelling unit. However, in no case shall private deed or other property restrictions be applied or recognized so as to permit a lesser standard than the minimum standards established in this title or to otherwise revise the standards established by this title.

Rural Residential Requirements.

Slope-Density-Natural Area Relationship. The maximum density (du/ac) and the minimum percent of a site to remain in a natural state shall be determined by a slope analysis applied to the Slope-Density-Natural Area Table, as defined below.

Slope-Density-Natural Area Table 9.03.040-4.

Slope Class	Allowable Density (DU/Acre)	Amount of Open Space Required
Greater than 25%	0.05 (1 du/20 ac)	60%
15.1% to 25%	0.10 (1 du/10 ac)	50%
10% to 15%	0.20 (1 du/5 ac)	35%
Less than 10%	0.40 (1 du/2.5 ac)	n/a

Slope analysis calculations and mapping shall be provided by the applicant as described under subsection C of this section. The slope analysis shall be certified by a qualified civil engineer or licensed surveyor.

The total number of dwelling units permitted within a project area shall be the sum of the allowable dwelling units within each slope class. For example, if 10 acres of the project falls within the 10 to 15% slope class and five acres falls within the 15.1% to 25% slope class, then the total permitted yield shall be two dwelling units (10 ac x 0.10 du/ac plus 5 ac x 0.20 du/ac).

Minimum Lot Size. Minimum lot size shall be one dwelling unit per two and one-half acres within a slope category of 10% or less unless determined to be reduced by an approved slope analysis. Based on the outcome of a slope analysis, minimum lot size within the rural residential district may be reduced to 20,000 square feet, or the minimum lot size of the adjacent zone, whichever is greater, if clustered on slopes of less than 10% and the lots are part of a project that preserves the steeper slope classes as natural open space by dedication to an appropriate governmental entity, open space easement, transfer of development rights or other means approved by the city. The ongoing maintenance of such open space areas shall be ensured through a mechanism approved by the city.

Subdivision Design and Future Land Divisions.

Subdivisions shall be compatible with the surrounding development pattern. A subdivision shall be considered compatible if the lots created along the outside boundary of the project are no smaller than the average lot size within 300 feet of the project boundary. Parcels greater than five acres in area shall be excluded from the calculations when determining the average lot size within 300 feet of the project boundary.

Subdivisions shall be designed in such a way as to transfer development density to the lower slope classes and preserve the steeper slopes for very low density and/or open space. Subdivisions created in this way are prohibited from further division so as not to circumvent the density transfer and the purpose of the district. This restriction shall be binding on the subdivider and subsequent land owners. Therefore, this restriction shall be secured by development agreement or other type of recorded deed restriction approved by the city.

Building Height. Dwellings and other accessory structures shall not exceed 30 feet in overall height, provided that on slopes of less than 10%, the overall height shall not exceed 35 feet.

Setbacks and Other Site Development Criteria. Front, side and rear setbacks and other site development standards not specifically referenced in this section shall be subject to the following standards:

Lot Size	Standards
Under 40,000 s.f.	R2 district standards
40,000 s.f. or greater	R1 district standards

Grading within the rural residential district shall be performed as described under the hillside residential requirements, subsection (B)(6) of this section.

Hillside Residential Requirements.

Slope-Density-Natural Area Relationship. The maximum density (du/ac) and the percent of a site to remain in a natural state shall be determined by a slope analysis applied to the Slope-Density-Natural Area Table, as defined below.

Slope-Density-Natural Area Table 9.03.040-5.

Slope Class	Allowable Density (DU/Acre)	Minimum Amount of Open Space Required
Greater than 25%	0.10 (1 du/10 ac)	60%
15.1% to 25%	0.25 (1 du/4 ac)	50%
10% to 15%	0.50 (1 du/2 ac)	35%
Less than 10%	1.00 (1 du/ac)	n/a

Slope analysis calculations and mapping shall be provided by the applicant as described under subsection C of this section. The community development director may require the slope analysis to be certified by a qualified civil engineer or licensed surveyor.

The total number of dwelling units permitted within a project area shall be the sum of the allowable dwelling units within each slope class. For example, if 10 acres of the project falls within the 15.1% to 25% slope class and five acres falls within the greater than 25% slope class, then the total permitted yield shall be three dwelling units (10 ac x 0.25 du/ac plus 5 ac x 0.10 du/ac).

Minimum Lot Size. Minimum lot size shall be one acre within a slope category of 10% or less unless determined to be reduced by an approved slope analysis. Based on the outcome of a slope analysis, the lot size within the hillside residential district may be reduced to 10,000 square feet or the minimum lot size of the adjacent zone, whichever is greater, if clustered on slopes of less than 10% and the lots are part of a project that preserves the steeper slope classes as natural open space by dedication to an appropriate governmental entity, open space easement, transfer of development rights or other means approved by the city. The ongoing maintenance of such open space areas shall be ensured through a mechanism approved by the city.

Subdivision Design and Future Land Divisions.

Building Height. Dwellings and other accessory structures shall not exceed 30 feet in overall height, provided that on slopes of less than 10%, the overall height shall not exceed 35 feet.

Lot Size	Standards
Less than 20,000 s.f.	R-3 district standards
20,000 s.f. to 40,000 s.f.	R-2 district standards
40,000 s.f. or greater	R-1 district standards

Grading of any site shall be minimized and shall conform to the provisions contained in the city of Moreno Valley design guidelines, Ch. 9.16, under applications for hillside development, Article IV, Sections 9.16.170 through 9.16.235 of this title, and the following standards:

Slope Class	Standards
15.1—25%	Padded building sites may be allowed, but maximum use of custom foundations and split level designs shall be employed to reduce the need for large, padded building areas.
Above 25%	Mass grading is not permitted. Special hillside architectural and design techniques are expected in order to conform to the natural landform. Homes constructed on lots within this terrain shall use custom, multiple-level foundations.
For all areas	All graded areas shall be protected from wind and water erosion through acceptable slope stabilization methods such as planting, walls or jute netting.

Slope Calculations. For the purposes of this section, the following method will be used to determine slope.

"Slope" is defined as the relationship between the change in elevation (rise) of the land and the horizontal distance (run) over which that change in elevation occurs. The percent of any given slope is determined by dividing the rise by the run on the natural slope of land, multiplied by 100.

For the purpose of determining the amount and location of land falling into each slope category, the applicant shall submit to the community development department, at the time of application, a base topographic map of the subject site prepared and signed by a registered civil engineer or licensed land surveyor. Such a map shall have a scale of not less than one inch to 200 feet and a contour interval of not more than 10 feet.

This base topographic map shall include all adjoining properties within 300 feet of the site boundaries. Slope bands in the range of less than 10%, 10 to 15%, 15 to 25%, and greater than 25% shall be delineated on the topographic map. The map shall be accompanied by a tabulation of the land area in each slope category specified in acres. The exact method for computing the percent slope and area by percent slope category is to be sufficiently described and presented so that a review can readily be made.

Slope Mapping Method.

The percent slope of any particular piece of land shall be plotted on the map as described in this subsection.

In preparing a slope map, those portions of ravines, ridges and terraces of less area generally sloping at 25% slope or greater, shall be regarded as part of the bordering 25% slope or greater band.

General Residential Requirements. The following tables sets forth minimum site development standards for residential development projects in the specified residential districts. In addition, projects must comply with the special development standards enumerated in this section, the performance standards included in Chapter 9.10 and any other applicable city ordinances, policies and standards.

Table 9.03.040-6 Residential Site Development Standards Single-Family Standards
Requirement			R1	R2	RA2	R3	R5	RS10
1.	Maximum density (DUs* per net acre)		1	2	2	3	5	10
2.	Minimum lot size (sq. ft. net area)		40K**	20K	20K	10K	7,200	4,500
3.	Minimum lot width, in feet		150	100	100	90	70	45
Cul-de-sac/knuckle lot frontage			50	50	50	50	50	45
4.	Minimum lot depth, in feet		170	120	120	100	100	85
5.	Minimum front yard setback		25	25	25	25	20	20
Front-facing garages								10
Buildings other than front-facing garages								10
6.	Minimum side yard setback, in feet***
	a.	Interior side yard	See Note 1	See Note 1	See Note 1	See Note 1	See Note 2	See Note 3
	b.	Street side yard	20	20	20	15	15	10
7.	Minimum rear yard setback, in feet***		40	35	35	30	15	15
8.	Maximum lot coverage		25%	30%	30%	40%	40%	50%
9.	Maximum building and structure height, in feet		Two stories not to exceed 35 feet.
10.	Minimum dwelling size (sq. ft.)		1500	1500	1500	1250	1250	1000
11.	Minimum distance between buildings, in feet (including main DUs and accessory structures)		20	15	15	10	10	10
12.	Floor area ratio
	a.	One-story home	0.25	0.30	0.30	0.40	0.40	0.50
	b.	Multi-story home	0.50	0.60	0.60	0.70	0.70	0.75

Notes to Residential Site Development Standards Table 9.03.040-6.
*	The term "DUs" means dwelling units.
**	The term "K" means thousands.
***	See Section 9.08.030 regarding accessory structures and room additions.
1.	Combined interior side yard setbacks of 20 feet shall be provided with a minimum of five feet on one side.
2.	Combined interior side yard setbacks of 15 feet shall be provided with a minimum of five feet on one side.
3.	In the RS10 district the minimum street side setback shall be 10 feet. The interior side setback shall be five feet, except in the case of zero lot line developments with houses placed on an interior side lot line. When a house is placed on an interior side lot line, the other minimum side yard setback shall be 10 feet. Where applicable, an easement at least five feet in width shall be provided along the common lot line. The easement shall guarantee the right to use and occupy the easement for a roof overhang(s), stormwater drainage and for building maintenance and repair.
4.	The minimum front yard setback from private streets within the R1, R2 and R3 districts shall be 55 feet measured from the center line of the street. The minimum front yard setback from private streets within the R5 district shall be 50 feet measured from the center line of said street.

Table 9.03.040-7 Residential Site Development Standards Multifamily Standards
Requirement		R10	R15	R20	R30
1.	Maximum density (DUs*/net acre)	10	15	20	30
2.	Minimum lot size (net area in sq. ft.)**	1 acre	1 acre	1 acre	1 acre
3.	Minimum lot width in ft.	200	200	200	200
4.	Minimum lot depth in ft.	175	175	175	175
5.	Minimum front yard setback, in ft.	20	25	30	30
6.	Minimum side yard setback, in ft.
	Interior side yard	10	10	10	10 ft. plus 2 ft. for every 5 ft. in height over 30 ft.
	Street side yard	20	20	20	20
7.	Minimum rear yard setback, in ft.	15	20	25	10 ft. plus 2 ft. for every 5 ft. in height over 30 ft.
8.	Maximum lot coverage	40%	45%	50%	50%
9.	Maximum building and structure height, in ft.	50 feet
10.	Minimum dwelling size (sq. ft.)	See Note 1
11.	Minimum distance between buildings, in ft. (including main DUs and accessory structures)	20	20	20	20
12.	Floor area ratio	0.75	0.75	0.75	1.0

NOTES:
*	The term "DUs" means dwelling units.
**	Minimum lot size only applies to newly subdivided multifamily lots; existing lots can be developed under the multifamily development standards.

Special Single-Family Residential Development Standards.

In any residential district, front yard setbacks in subdivision developments may be reduced by 20% provided the mean of all such setbacks in the development is not less than the minimum required for the district.

In the R2, RA2, R3 and R5 districts, developments of five or more dwelling units shall include front and street side yard landscaping and shall consist predominantly of plant materials, except for necessary walks, drives and fences.

In the RS10 district, driveways and fire hydrants shall be designed and located to maximize on-street parking opportunities in front of each residence.

Within the RS10 district, small lot single-family subdivisions on less than 15 gross acres shall provide landscaping and decorative walls along the street side of corner lots and at least two of the following amenities throughout the project:

Front porches;

Automatic garage door openers;

Electronic security systems.

Within the RS10 district, small lot single-family subdivisions on 15 gross acres or more shall include usable common open space encompassing a minimum of 10% of each development. Usable common open space does not include individually owned lots, parking areas, nor vehicular rights-of-way. Usable common open space is open space and/or recreational amenities under joint (common) ownership, including, but not necessarily limited to, landscaped areas, trails, playgrounds, tennis courts, swimming pools and recreational buildings. A homeowners' association shall be established to provide continual maintenance of the commonly owned facilities.

For all developments within the R5 land use district, a buffer of lots held to the development standards of the R3 land use district shall be included for all portions of a subdivision located adjacent to lower density single-family residential land use districts, including the R1, R2, RA-2, and RR zones.

For all single-family residential developments in the R10, R15, R20, and R30 districts a planned unit development application shall be submitted to establish the applicable development standards.

In all residential districts, air conditioners, heating, cooling and ventilating equipment and all other mechanical, lighting or electrical devices shall be operated so that noise levels do not exceed 60 dBA (Ldn) at the property line. Additionally, such equipment, including roof-mounted installation, shall be screened from surrounding properties and streets and shall not be located in the required front yard or street side yard. All equipment shall be installed and operated in accordance with other applicable city ordinances.

Special Multiple-Family Residential Development Standards.

In the R10, R15, R20 and R30 districts, buildings exceeding one story in height shall maintain a minimum building setback of 50 feet from any single-family district. Any single-story building within the R10, R15, R20 or R30 district shall maintain a minimum setback of 20 feet from any single-family district.

In the RS10, R10, R15, R20 and R30 districts, developments of five or more dwelling units shall include front and street side yard landscaping and shall consist predominantly of plant materials, except for necessary walks, drives and fences.

In the RS10, R10, R15, R20 and R30 districts, a minimum of 35% of the net site area, exclusive of private patio and yard areas, shall be landscaped. Turf shall not exceed 50% of this area. Required setback areas and outdoor recreation areas may be counted toward this minimum. Landscaping shall consist predominately of plant materials to include water efficient native plants, except for necessary walks and fences. Landscape areas shall be designed to promote water retention and allow runoff from impervious surfaces. Hardscape areas are recommended to be constructed with pervious surfaces where feasible to reduce run off.

Where a multiple-family project abuts property in a single-family district, a decorative masonry wall at least six feet in height and screening landscaping within a planter of at least five-foot interior width shall be erected and maintained between such uses and the single-family district. Decorative walls composed of block, brick, stone, stucco-treated masonry or concrete panels are acceptable. The community development director may approve alternative materials, provided that the materials are decorative and comparable to masonry walls or concrete panels in durability and ability to attenuate light and sound.

Parking for each use shall comply with the requirements of Chapter 9.11 of this title.

In the R30 District, Landscape Trees. One tree per 20 linear feet of building dimension for the portions of building visible from parking lot or ROW and one tree per 20 linear feet of perimeter planter areas.

In the R30 district, for a development of three acres or greater, up to 60% of the units may be in buildings with three or four stories, 50 feet maximum height subject to planning commission approval.

Table 9.03.040-8
Designation	Minimum Density*	Maximum Density
R10	8 units/acre	10 units/acre
R15	12 units/acre	15 units/acre
R20	16 units/acre	20 units/acre
R30	24 units/acre	30 units/acre

*	Eighty percent of allowable density must be achieved by all multiple-family residential developments.

General Multiple-Family Guidelines.

Opposing garages or carports should be turned to avoid the monotony of alley-like parking corridors.

Parking areas should be staggered and landscaped to add visual interest, and opportunities for accent treatments.

Parking spaces within multifamily areas shall be located within 250 feet of the dwellings they serve.

Multifamily parking lots shall be limited to two double aisles of cars to help reduce expanses of paving. Parking lots shall provide openings in curbs to convey surface drainage into landscape areas for water quality, retention and absorption.

Open parking areas should be clustered and treated as landscaped plazas and courts.

Landscaping shall be used around the perimeter of the lot, as well as within the lot, reducing paved area and providing for a more pedestrian oriented site.

No more than four units for a two-story structure should be served by one entry.

Each multiple-family unit shall have at least 150 square feet of private open space per downstairs unit and a minimum of 100 square feet of private open space per upstairs unit. Private open space may consist of a fenced yard area, patio or balcony. Fenced yards and patios shall have a minimum dimension of at least eight feet. Balconies shall be at least five feet deep.

Common open space at a minimum of 300 square feet per each residential dwelling in the project is required.

10.

Individual units should have a porch or porch-like space at the front door.

11.

Trash enclosures shall be located to provide a maximum walking distance of 250 feet from the units they serve.

12.

Trash enclosures shall include solid roofs and be designed to be compatible with the project's architecture.

13.

Trash enclosures shall not be located on dead end drive aisles, unless adequate turnaround is provided for collection vehicles.

14.

There shall be at least one double-bin trash enclosure for every 48 residential units.

15.

Mail boxes should be located at various places on the site and treated to match the building's architecture, avoiding the institutional and monumental "gang box" appearance, while conforming to post office guidelines.

16.

Drive aisles should be curved and should incorporate landscaping and paving treatments to reduce vehicle speed. Landscaping treatments may include pinched planters and a mix of canopy and vertical trees. Paving treatments may include interlocking paver bands or etchings across drives. Speed bumps or Botts' dots are not an acceptable alternative.

17.

Freestanding structures, like gazebos or pergolas, should be located to define activity areas at pathway intersections or in secluded landscape areas.

18.

Drive aisles shall be at least 24 feet wide for two-way traffic and shall be at least 20 feet wide for one-way traffic.

19.

Buffer setbacks and landscaping shall be provided along all property lines. Buffers may also be appropriate within the complex, separating recreational areas from units and limiting lines of sight between balconies and into parking areas.

20.

Multiple-family projects warrant special design considerations, including:

Intimate, shaded outdoor seating areas;

A network of pathways, providing interesting walking experiences;

Gentle slopes for outdoor pathways and ramps to entry doors and between floors;

Convenient and attractive access to transit, including porte cocheres, information kiosks, seating areas and water elements;

Security;

Direct ambulance access (senior housing projects);

Parking close to units;

Elevators (senior housing projects).

21.

Multifamily units shall be clustered to minimize grading and to help maintain the natural landscape.

22.

Multifamily projects shall be designed for the needs of the intended residents. For example, children's needs would require open space, tot lots, handrails, and enclosed yards on ground floor units. Disabled or elderly needs would require ramps, parking close to units, minimum and gradual elevation changes and elevators.

23.

Architectural features should be used to increase privacy from nearby units and common or public spaces.

24.

Roof forms should be mixed and combined to vary the perception of building height, to differentiate units and to add interest to building mass. The long, straight roofline of a single gable is not permitted.

25.

A diagram of the complex showing the location of the viewer and the building designations shall be positioned at each visitor entrance of a multiple-family development.

26.

Buildings shall provide for a variety of colors and architectural features to break up the massing of buildings and provide visual interest.

(Ord. 359, 1992; Ord. 386 § 1.13, 1993; Ord. 461 § 1.1, 1995; Ord. 468 §§ 1.4, 1.5, 1995; Ord. 475 § 1.4,, 1995; Ord. 520 § 1.9, 1997; Ord. 604 § 2.3, 2002; Ord. 616 §§ 2.2.1, 2.2.2, 2003; Ord. 694 § 1.1, 2005; Ord. 698 § 3.1(c), 2005; Ord. 726 § 4.3, 2006; Ord. 757 §§ 2.7, 2.7.2, 2008; Ord. 757 §§ 2.7, 2.72, 2008; Ord. 773 § 3, 2008; Ord. 797 §§ 2.4, 2.4.2—4, 2009; Ord. 808 §§ 2.2—2.2.3, 2010; Ord. 826 § 3.2, 2011; Ord. 869 §§ 3.12, 3.13, 2013; Ord. 912 § 13, 2016; Ord. 984 § 3, 2022; Ord. 994 § 6, 2023; Ord. 1005, 12/19/2023; Ord. 1013, 6/25/2024)

§ 9.03.050 Density bonus program for affordable housing.

Purpose and Intent. This section is adopted pursuant to the provisions of California Government Code Sections 65915 through 65918, as they now exist or may hereafter be amended. The purpose of adopting this section is to encourage affordable housing by providing the incentive of increased density and such other incentives provided by this section. The provisions of this section are intended to comply with California Government Code Sections 65915 through 65918. In the event that any provision of this section conflicts with California Government Code Sections 65915 through 65918, state law shall control over the conflicting provision.

Applicability. A housing development as defined in this section and Government Code Section 65915 shall be eligible for a density bonus and other incentives that are provided by State Density Bonus Law when the applicant agrees to construct low, very low, senior or moderate income housing units or units intended to serve transitional foster youth, disabled veterans, and lower income students as specified in this section and State Density Bonus Law.

Application Requirements. A density bonus may be approved pursuant to an application for approval of a density bonus, provided the request complies with the provisions of this section. An application for a density bonus incentive, concession, waiver, or modifications of development standards pursuant to this section, shall be submitted with the first application for approval of a housing development and processed concurrently with all other applications required for the housing development. The application shall be submitted on a form prescribed by the city and shall include at least the following information:

A site plan that identifies all units in the project, including the location of the affordable units and the bonus units.

A narrative briefly describing the housing development and shall include information on:

The number of units permitted under the general plan;

The total number of units proposed in the project, including the floor area, and the number of bedrooms and bathrooms associated with each dwelling unit. Density bonus units shall have at least the same distribution of bedrooms as the market rate units in the development. Density bonus units shall be constructed concurrently with the construction of market rate units;

Target income of affordable housing units and proposals for ensuring affordability;

The number of bonus units requested based on subsection E.3 of this section.

Description of Any Requested Incentives, Concessions, Waivers, or Modifications of Development Standards. For all incentives and concessions that are not included within the menu of incentives/concessions set forth in subsections G and H of this section, the application shall include a pro forma providing evidence that the requested incentives and concessions result in identifiable, financially sufficient, and actual cost reductions. The cost of reviewing any required pro forma or other financial data submitted as part of the application in support of a request for an incentive/concession or waiver/modification of developments standard, including, but not limited to, the cost to the city of hiring a consultant to review said financial data, shall be borne by the developer. The pro forma shall include all of the following items:

The actual cost reduction achieved through the incentive;

Evidence that the cost reduction allows the applicant to provide affordable units or affordable sales prices; and

Other information requested by the community development director. The community development director may require that any pro forma include information regarding capital costs, equity investment, debt service, projected revenues, operating expenses, and such other information as is required to evaluate the pro forma.

Any such additional information in support of a request for a density bonus as may be requested by the community development director.

Eligibility for Bonus. A developer of a housing development containing five or more units may qualify for a density bonus and at least one other incentive as provided by this section if the developer does one of the following:

Agrees to construct and maintain at least five percent of the units dedicated to very low income households;

Agrees to construct and maintain at least 10% of the units dedicated to lower income households;

Agrees to construct and maintain at least 10% of the units in a common interest development (as defined in Section 4100 of the California Civil Code) dedicated to moderate-income households, provided that all units in the development are offered to the public for purchase;

Agrees to construct and maintain a senior citizen housing development, as defined in Section 9.09.150 of this title, or a mobile home park that limits residency based on age requirements for housing for older persons pursuant to Section 798.76 or 799.5 of the California Civil Code;

Land Donations. An applicant for a tentative subdivision map, parcel map, or other residential development approval that donates land to the city in accordance with Government Code Section 65915(g) shall be eligible for a density bonus in accordance with the terms and conditions of Government Code Section 65915(g);

Includes a qualifying child care facility as described in subsection J.2 (child care facility requirements) of this section in addition to providing housing as described in subsections D.1 through 3 of this section;

Agrees to construct and maintain at least 10% of the units of a housing development for transitional foster youth, as defined in Section 66025.9 of the California Education Code; disabled veterans, as defined in Section 18541 of the California Government Code; or homeless persons, as defined in the Federal McKinney-Vento Homeless Assistance Act (42 U.S.C. Section 11301 et seq.), dedicated to very low-income households;

Agrees to construct and maintain at least 20% of the units for lower income students in a student housing development dedicated for students enrolled full time to allow the units to be used by undergraduate, graduate, or professional students enrolled currently or in the past six months in at least six (6) units at accredited colleges pursuant to the student housing subsection K of this section; or

Agrees to construct and maintain 100% of the units, including total units and density bonus units, but exclusive of a manager's unit or units, dedicated to lower-income households, except that no more than 20% of the units, including total units and density bonus units, may be dedicated to moderate income households.

10.

Religious institution-affiliated housing development projects (RIAHD) may qualify for a density bonus under California Government Code Section 65915. For RIAHD parking requirements, see Section 9.11.040(D).

Density Bonus Calculation and Allowance.

State Law Preemption. Pursuant to state law, the granting of a density bonus or the granting of a density bonus together with an incentive(s) shall not be interpreted, in and of itself, to require a general plan amendment, specific plan amendment, rezone, or other discretionary approvals.

Density Bonus Calculation. An applicant must choose a density bonus from only one applicable affordability category and may not combine categories with the exception of childcare facilities or land donation, which may be combined with an affordable housing development. All density calculations resulting in fractional units will be rounded up to the next whole number.

Density Bonus Allowance. In calculating the number of units required for very low, lower, and moderate-income households, the density bonus units shall not be included. The maximum bonus allowed for a 100% affordable project is 80% unless it is located within one-half mile of a major transit stop, and then there is no limit to density. A housing development that satisfies all applicable provisions of this section shall be allowed the following applicable density bonuses:

Very low income per California Government Code Section 65915(f)(2).

Lower income per California Government Code Section 65915(f)(1).

Moderate income per California Government Code Section 65915(f)(4).

Senior Citizen Housing Development. The density bonus for a senior citizen housing development is addressed in Section 9.09.150 (Senior citizen housing) of Chapter 9.09 (Specific Use Development Standards).

Residential care facilities for the elderly (RCFEs), which include assisted living, qualify as a type of senior citizen housing development that can receive density bonus incentives for restricted, affordable units. RCFEs may qualify as shared housing pursuant to subsection L of this section.

Child Care Facility. A project (whether a housing, commercial, or industrial project) is eligible for a density bonus for a child care facility when in compliance with this section and California Government Code Section 65917.5.

Conversion of Apartments to Condominiums. A project is eligible for a 25% density bonus for the conversion of apartments to condominiums when in compliance with California Government Code Section 65915.5.

Foster Youth, Disabled Veterans, and Homeless Persons. The density bonus for a housing development for transitional foster youth, disabled veterans, or homeless persons shall be 20%.

Students. The density bonus for a student housing development that provides housing for students consistent with subsection K of this section shall be 35%. 20% of the units granted by the density bonus shall be used for lower income students.

10.

100% Affordable. The density bonus for a 100% affordable housing development consistent with subsection D.9 (Eligibility for Bonus) of this section shall be 80% of the number of units for lower income households. Except that if the affordable housing development is located within one-half mile of a major transit stop, maximum density requirements shall not apply.

A non-residential development may obtain additional non-residential floor area or other development incentives. The required affordability can be satisfied through an agreement for partnered housing with an affordable housing developer pursuant to the requirements of pursuant to Section 65915.7 of the Government Code.

Continued Affordability. Prior to issuance of a building permit, the developer/property owner must enter into a density bonus housing agreement with the city for at least 55 years by recorded document (Government Code Section 65915(c)). Such agreement shall be recorded and shall be binding on the property owner and any successors-in-interest. In addition, a density bonus project must comply with specific requirements for any existing units that are to be demolished as outlined in subsection Q of this section. Additional details regarding requirements for continued affordability and the density bonus housing agreement are included in subsection P.

Incentives Available to Housing Projects. Incentives are available to housing development are as follows:

Number of Incentives/Concessions	Very Low Income Percentage	Lower Income Percentage	Moderate Income Percentage
1	5%	10%	10%
2	10%	17%	20%
3	15%	24%	30%
4	16%	26%	45% (for sale units)
5	100% low/very low/mod (20% moderate allowed)*	100% low/very low/mod (20% moderate allowed)*	100% low/very low/mod (20% moderate allowed)*

Note:
If the project is located within one-half mile of a major transit stop, the applicant shall also receive a height increase of up to three additional stories, or 33 feet.

Available Incentives/Concessions. A qualifying project may be entitled to up to four incentives, depending on the percentage of affordable housing that will be included within the development.

A concession falls within three categories (California Government Code Section 65915(k)(1), (2) and (3)).

Reduction in the site development standards of this development code (e.g., site coverage, off-street parking requirements, reduced lot dimensions, and/or setback requirements);

Approval of mixed-use zoning in conjunction with the housing project if commercial, office, industrial, or other land uses will reduce the cost of the housing development and if such uses are compatible with the housing project and the existing or planned development in the area; and/or

Other regulatory incentives or concessions proposed by the developer or the city that will result in identifiable and actual cost reductions.

Additional Incentive/Concession. The developer may receive a 50% reduction of the development impact fee and the parkland impact mitigation fee for the units affordable to very low income households and a 25% reduction for those units affordable to lower- income households.

Parking Requirements. If an applicant qualifies for a density bonus pursuant to this section, reduced parking requirements are available for projects qualifying for a density bonus pursuant to this section. The parking requirement is inclusive of accessible and guest parking for the entire housing development, but shall not include on-street parking spaces in the count towards the parking requirement. In calculating the number of parking spaces required for a development, if the total number of parking spaces is other than a whole number, the number shall be rounded up to the next whole number.

Except as otherwise provided in this subsection, the following parking requirements shall apply:

Zero to one bedroom: one on-site parking space.

Two to three bedrooms: one and one-half on-site parking spaces.

Four or more bedrooms: two and one-half on-site parking spaces.

If the housing development includes at least 20% lower income units or at least 11% very low income units, is located within one-half mile of a major transit stop, and there is unobstructed access to the major transit stop from the development, then the parking requirement shall be reduced from one-half on-site parking space per bedroom to one- half on-site parking space per unit.

If a housing development consists solely of rental units, exclusive of a manager's unit or units, with an affordable housing cost to lower income families, as provided in Section 50052.5 of the California Health and Safety Code, then no parking spaces shall be required as long as the development meets either of the following criteria:

The development is located within one-half mile of a major transit stop and there is unobstructed access to the major transit stop from the development; or

The development is a for-rent housing development for individuals who are 62 years of age or older that complies with Sections 51.2 and 51.3 of the California Civil Code and the development has either paratransit service or unobstructed access, within one-half mile, to fixed bus route service that operates at least eight times per day.

If a housing development consists solely of rental units, exclusive of a manager's unit or units, with an affordable housing cost to lower income families, as provided in Section 50052.5 of the California Health and Safety Code, and the development is either a special needs housing development, as defined in Section 51312 of the California Health and Safety Code, or a supportive housing development, as defined in Section 50675.14 of the California Health and Safety Code, then no parking spaces shall be required. A development that is a special needs housing development shall have either paratransit service or unobstructed access, within one-half mile, to fixed bus route service that operates at least eight times per day.

Number of Bedrooms	Required Parking Spaces per Unit,*
0 to 1 bedroom	1
2 to 3 bedrooms	1.5
4 or more bedrooms	2.5
Projects with at least 20% low-income units, or at least 11% very low income units***	0.5
100% affordable housing projects****	No requirement

NOTES:
*	If the total number of spaces required results in a fractional number, it shall be rounded up to the next whole number.
**	If a residential or mixed residential/commercial development project includes the required percentage of low, very low income, or includes a minimum 10% transitional foster youth, veteran, or homeless persons units, or provides for-rent housing for individuals who are 62 years of age or older, or is a special needs housing development and is located within one-half mile of a major transit stop where there is unobstructed access to a major transit stop from the development, then, upon the request of the developer, a parking ratio not to exceed 0.5 spaces per bedroom shall apply to the residential portion of the development.
***	Must be located within one-half mile of a major transit stop, with unobstructed access to the major transit stop from the development.
****	Must be located within one-half mile of a major transit stop, with unobstructed access to the major transit spot from the development OR for individuals 62 years of age or older and has either paratransit service or unobstructed access within one-half mile, to fixed bus route service that operates at least eight times per day.

Child Care Facilities.

Child Care Facility Density Bonus. When an applicant proposes to construct a housing development that is eligible for a density bonus under subsection D (Eligibility for Bonus) of this section and California Government Code Section 65917.5, and includes a child care facility that will be located on the premises or adjacent to the housing development, the city shall grant either:

An additional density bonus that is an amount of square feet of residential space that is equal to or greater than the square footage of the child care facility; or

An additional incentive that contributes significantly to the economic feasibility of the construction of the child care facility.

Child Care Facility Requirements. The city shall require, as a condition of approving the housing development, that the following occur:

The child care facility shall remain in operation for a period of time that is as long as or longer than the period of time during which the affordable units are required to remain affordable per this section; and

Of the children who attend the child care facility, the children of very low income households, lower income households or families of moderate income households shall equal a percentage that is equal to or greater than the percentage of affordable units in the housing development that are required for very low, lower or families of moderate income households.

Child Care Facility Criteria. The city shall not be required to provide a density bonus or incentive for a child care facility if it finds, based upon substantial evidence, that the community has adequate child care facilities.

Student Housing.

Student Housing Density Bonus Requirements. In order for a student housing development to be eligible for a density bonus under subsection D.8 of this section, the student housing development must meet the following requirements:

All units in the student housing development shall be used exclusively for undergraduate, graduate, or professional students enrolled currently or in the past six months in at least six units at an institution of higher education accredited by the Western Association of Schools and Colleges or the Accrediting Commission for Community and Junior Colleges. The developer shall, as a condition of receiving a certificate of occupancy, provide evidence to the city that the developer has entered into an operating agreement or master lease with one or more institutions of higher education for the institution or institutions to occupy all units of the student housing development with students from that institution or institutions.

20% of the density bonus units will be used for lower income students. For purposes of this clause, "lower income students" means students who have a household income and asset level that does not exceed the level for Cal Grant A or Cal Grant B award recipients as set forth in paragraph (1) of subdivision (k) of Section 69432.7 of the California Education Code.

One incentive or concession will be granted for projects that include at least 20% of the total units for lower income students in a student housing development. If a project includes at least 23% of the total units for lower income students in a student housing project, the applicant shall instead receive two incentives or concessions.

The rent provided in the applicable units of the development for lower income students shall be calculated at 30% of 65% of the area median income for a single-room occupancy unit type.

The development will provide priority for the applicable affordable units for lower income students experiencing homelessness.

Definition of Units. For purposes of calculating a density bonus granted for a student housing development, the term "unit" means one rental bed and its pro rata share of associated common area facilities.

Shared Housing.

Shared Housing Density Bonus Requirements. In order for a shared housing development to be eligible for a density bonus under subsection D.1, D.2, D.4 or D.9, of this section, the shared housing development must meet the following requirements:

Shared-housing building is defined as a residential or mixed-use structure with five or more housing units and one or more common kitchens and dining areas designed for permanent residence of more than 30 days by its tenants. The kitchens and dining areas within the shared housing building shall be able to adequately accommodate all residents.

A shared housing building may include other dwelling units that are not shared housing units, provided that those dwelling units do not occupy more than 25% of the floor area of the shared housing building.

A shared housing building may include incidental commercial uses, provided that those commercial uses are otherwise allowable and are located only on the ground floor or the level of the shared housing building closest to the street or sidewalk of the shared housing building.

A "shared housing unit" means one or more habitable rooms, not within another dwelling unit, that includes a bathroom, sink, refrigerator, and microwave, is used for permanent residence, that meets the "minimum room area" specified in Section R304 of the California Residential Code (Part 2.5 of Title 24 of the California Code of Regulations) and complies with the definition of "guestroom" in Section R202 of the California Residential Code.

Shared housing shall permit the same number of families at the same density as allowed in the zoning district where the property is located subject to all applicable codes relating to building, housing, life safety, health and zoning as would be applied to independent living units located in the same structure.

Definition of Units. For purposes of calculating a density bonus granted for a shared housing development, the term "unit" means one shared housing unit and its pro rata share of associated common area facilities.

General Guidelines.

Location of Bonus Units. As required by California Government Code Section 65915(i), the location of density bonus units within the qualifying housing development may be at the discretion of the developer and need not be in the same area of the project where the units for the lower income households are located as long as the density bonus units are located within the same housing development.

Preliminary Review. A developer may submit to the community development director a preliminary proposal for the development of housing pursuant to this section prior to the submittal of any formal application for a density bonus. Within 90 days of receipt of a written proposal, the city will notify the housing developer in writing of either: (a) any specific requirements or procedures under this section, which the proposal has not met; or (b) the proposal is sufficient for preparation of an application for density bonus.

Infrastructure and Supply Capacity. Criteria to be considered in analyzing the requested bonus will include the availability and capacity of infrastructure (water, sewer, road capacity, etc.) and water supply to accommodate the additional density.

Findings for Approval for Density Bonus and/or Incentive(s).

Density Bonus Approval. The following finding shall be made by the approving authority in order to approve a density bonus request:

The density bonus request meets the requirements of this section.

Density Bonus Approval with Incentive(s). The following findings shall be made by the approving authority in order to approve a density bonus and incentive(s) request:

The density bonus request meets the requirements of this section;

The incentive is required in order to provide affordable housing; and

Approval of the incentive(s) will have no specific adverse impacts upon health, safety, or the physical environment or on any real property that is listed in the California Register of Historical Resources and for which there is no feasible method to satisfactorily mitigate or avoid the specific adverse impact without rendering the development unaffordable to very low, low, and moderate income households.

Denial of a Request for an Incentive(s). The approving authority shall make at least one of the following findings prior to disallowing an incentive (in the case where an accompanying density bonus may be approved, or in the case of where an incentive(s) is requested for senior housing or child care facility):

That the incentive is not necessary in order to provide for affordable housing costs as defined in subsection S (Definitions) of this section, or for rents for the targeted units to be set as specified in subsection S (Definitions) of this section.

That the incentive would result in specific adverse impacts upon health, safety, or the physical environment or on any real property that is listed in the California Register of Historical Resources and for which there is no feasible method to satisfactorily mitigate or avoid the specific adverse impact without rendering the development unaffordable to very low, low, and moderate income households.

That the incentive would be contrary to state or federal law.

Affordability Requirements.

The maximum monthly housing cost for density bonus units, including a monthly allowance for utilities plus rent for rental units or house payments for for-sale units, shall be set at or below the rates described below:

Density bonus units affordable to very low income households: 30% of 50% of the area monthly median income for Riverside/San Bernardino Counties adjusted by the number of bedrooms according to regulations of the California Department of Housing and Community Development.

Density bonus units affordable to lower income households: 30% of 60% of the area monthly median income for Riverside/San Bernardino Counties adjusted by the number of bedrooms according to regulations of the California Department of Housing and Community Development.

The monthly allowance for utilities shall be the utility allowance calculated by the Department of Housing and Urban Development (HUD) for County Housing Authorities.

The monthly house payments for for-sale units described in subsection P.1 of this section includes the sum of principal and interest on a 30 year fixed rate mortgage for 90% of the sales price, loan insurance, property taxes and assessments, fire and casualty insurance, property maintenance and repairs, and the fair share cost for maintenance of amenities owned in common such as landscaping and swimming pools.

Housing costs, affordable sales prices, and occupancy requirements, will be governed by a deed restriction which shall take precedence over all other covenants, liens and encumbrances of the property on which the units are constructed.

Affordable Housing Agreement Required.

General Requirements. No density bonus pursuant to this section shall be granted unless and until the affordable housing developer, or designee enters into an affordable housing agreement and, if applicable, an equity sharing agreement, with the city or its designee pursuant to and in compliance with this section (Government Code Section 65915(c)). The agreements shall be in the form provided by the city, which shall contain terms and conditions mandated by, or necessary to implement, state law and this section. The affordable housing agreement shall be recorded prior to issuance of a building permit for a rental project or prior to final map recordation for an ownership project which includes a map. The community development director is hereby authorized to enter into the agreements authorized by this section on behalf of the city upon approval of the agreements by the city attorney for legal form and sufficiency.

Low or Very Low Income Affordable Housing Component.

The affordable housing developer of a qualified housing development based upon the inclusion of low income and/or very low income affordable units shall enter into an agreement with the city to maintain the continued affordability of the affordable units for 55 years (for rental units) or 30 years (for for-sale units), or a longer period if required by the construction or mortgage financing assistance program, mortgage insurance program or rental subsidy program (Government Code Section 65915(c)(1)). The agreement shall establish specific compliance standards and specific remedies available to the city if such compliance standards are not met. The agreement shall specify the number of lower income affordable units by number of bedrooms; standards for qualifying household incomes or other qualifying criteria, such as age; standards for maximum rents or sales prices; the person responsible for certifying tenant or owner incomes; procedures by which vacancies will be filled and units sold; required annual report and monitoring fees; restrictions imposed on lower income affordable units on sale or transfer; and methods of enforcing such restrictions, and any other information that may be required based on the city's review.

Rental Units. Rents for the low income and very low income affordable units that qualified the housing development for the density bonus pursuant to this section shall be set and maintained at an affordable rent (Government Code Section 65915(c)(1)). The agreement shall set rents for the lower income density bonus units at an affordable rent as defined in California Health and Safety Code Section 50053, except for developments meeting the criteria of Government Code Section 65915(b)(1)(G), for which rents for all units in the development, including both base density and density bonus units, shall be as follows:

The rent for at least 20% of the units in the development shall be set at an affordable rent, as defined in Section 50053 of the Health and Safety Code.

ii.

The rent for the remaining units in the development shall be set at an amount consistent with the maximum rent levels for a housing development that receives an allocation of state or federal low income housing tax credits from the California Tax Credit Allocation Committee.

The agreement shall require that owner-occupied units be made available at an affordable housing cost as defined in Health and Safety Code Section 50052.5.

For-Sale Units. Owner-occupied low income and very low income affordable units that qualify the housing development for the density bonus pursuant to this section shall be available at an affordable housing cost (Government Code Section 65915(c)(2)).

An applicant shall agree to ensure, and the city, county, or city and county shall ensure, that a for-sale unit that qualified the applicant for the award of the density bonus meets one of the following conditions:

(A)

The unit is initially sold to and occupied by a person or family of very low, low, or moderate income, as required, and it is offered at an affordable housing cost, as that cost is defined in Section 50052.5 of the Health and Safety Code and is subject to an equity sharing agreement.

ii.

If the unit is not purchased by an income-qualified person or family within 180 days after the issuance of the certificate of occupancy, the unit is purchased by a qualified nonprofit housing corporation that meets all of the following requirements pursuant to a recorded contract that satisfies all of the requirements specified in paragraph (10) of subdivision (a) of Section 402.1 of the Revenue and Taxation Code:

(A)

The nonprofit corporation has a determination letter from the Internal Revenue Service affirming its tax-exempt status pursuant to Section 501(c)(3) of the Internal Revenue Code and is not a private foundation as that term is defined in Section 509 of the Internal Revenue Code.

(B)

The nonprofit corporation is based in California.

(C)

All of the board members of the nonprofit corporation have their primary residence in California.

iii.

The primary activity of the nonprofit corporation is the development and preservation of affordable home ownership housing in California that incorporates within their contracts for initial purchase a repurchase option that requires a subsequent purchaser of the property that desires to resell or convey the property to offer the qualified nonprofit corporation the right to repurchase the property prior to selling or conveying that property to any other purchaser pursuant to an equity sharing agreement or affordability restrictions on the sale and conveyance of the property that ensure that the property will be preserved for lower income housing for at least 45 years for owner-occupied housing units and will be sold or resold only to persons or families of very low, low, or moderate income, as defined in Section 50052.5 of the Health and Safety Code.

The affordable housing developer of a qualified for-sale housing development based upon a very low- or low-income minimum affordable component shall enter into an equity sharing agreement with the city or the master or non-affordable housing developer. The agreement shall be between the city and the buyer, or between the developer and the buyer if the developer is the seller of the unit. The city shall enforce the equity sharing agreement unless it is in conflict with the requirements of another public funding source or law (Government Code Section 65915(c)(2)). The equity-sharing agreement shall include at a minimum the following provisions:

Upon resale, the seller of the unit shall retain the value of any improvements, the down payment and the seller's proportionate share of appreciation. The city shall recapture any initial subsidy, as defined in subsection Q.2.d.ii, and its proportionate share of appreciation, as defined in subsection Q.2.d.iii, which amount shall be used within five years for any of the purposes described in subdivision (e) of Section 33334.2 of the Health and Safety Code that promote homeownership.

ii.

For purposes of this section, the city's initial subsidy shall be equal to the fair market value of the home at the time of initial sale minus the initial sale price to the very low income household, plus the amount of any down payment assistance or mortgage assistance. If upon resale the market value is lower than the initial market value, the value at the time of the resale shall be used as the initial market value.

iii.

For purposes of this subdivision, the city's proportionate share of appreciation shall be equal to the ratio of the city's initial subsidy to the fair market value of the home at the time of initial sale.

iv.

If the unit is purchased or developed by a qualified nonprofit housing corporation pursuant to subsection Q.2.d.ii(A) the local government may enter into a contract with the qualified nonprofit housing corporation under which the qualified nonprofit housing corporation would recapture any initial subsidy and its proportionate share of appreciation if the qualified nonprofit housing corporation is required to use 100% of the proceeds to promote homeownership for lower income households as defined by Health and Safety Code Section 50079.5 within the jurisdiction of the local government.

Moderate Income Affordable Housing Component.

The affordable housing developer of a qualified housing development based upon the inclusion of moderate income affordable units in a common interest development shall enter into an agreement with the city ensuring that:

The initial occupants of the moderate-income affordable units that are directly related to the receipt of the density bonus are persons and families of a moderate income household.

ii.

The units are offered at an affordable housing cost (Government Code Section 65915(c)(2)). The affordable housing developer of a qualified housing development based upon a moderate income minimum affordable component shall enter into an equity sharing agreement with the city or the master or non-affordable housing developer (Government Code Section 65915(c)(2)). The agreement shall be between the city and the buyer or between the developer and the buyer if the developer is the seller of the unit. The city shall enforce the equity sharing agreement unless it is in conflict with the requirements of another public funding source or law (Government Code Section 65915(c)(2)). The equity sharing agreement shall include at a minimum the following provisions:

(A)

Upon resale, the seller of the unit shall retain the value of improvements, the down payment and the seller's proportionate share of appreciation. The city shall recapture any initial subsidy, as defined in subsection Q.3.a.iv, and its proportionate share of appreciation, as defined in Q.3.a.v, which amount shall be used within five years for any of the purposes described in Health and Safety Code Section 33334.2(e) that promote homeownership (Government Code Section 65915(c)(2)(A)).

iii.

The city's initial subsidy shall be equal to the fair market value of the unit at the time of initial sale minus the initial sale price to the moderate income household, plus the amount of any down payment assistance or mortgage assistance. If upon resale the market value is lower than the initial market value, the value at the time of the resale shall be used as the initial market value (Government Code Section 65915(c)(2)(B)).

iv.

The city's proportionate share of appreciation shall be equal to the ratio of the city's initial subsidy to the fair market value of the unit at the time of initial sale (Government Code Section 65915(c)(2)(C)).

Notwithstanding any other provision of law, a developer shall not sell a unit constructed pursuant to a local inclusionary zoning ordinance that is intended for owner-occupancy by persons or families of extremely low, very low, low, or moderate income to a purchaser that is not a person or family of extremely low, very low, low, or moderate income, except that if an income-qualifying person or family has not purchased such a unit within 180 days of the issuance of the certificate of occupancy a developer may sell the unit to a qualified nonprofit housing corporation that will ensure owner occupancy pursuant to the income limitation recorded on the deed or other instrument defining the terms of conveyance eligibility (Civil Code Section 714.7).

Ineligible Projects—Required Replacement of Affordable Units.

An applicant shall be ineligible for a density bonus or any other incentives or concessions under this section if:

The development is proposed on any property that includes any existing affordable rental dwelling units occupied by lower or very low income households; or

If such affordable dwelling units have been vacated or demolished in the five-year period preceding the application; and

Such affordable dwelling units have been subject to a recorded covenant, ordinance, or law that restricts rents to levels affordable to persons and families of lower or very low income. However, an applicant may establish eligibility if the proposed housing development replaces those units, and either of the following applies:

The proposed housing development, in addition to the units replaced pursuant to this paragraph, contains affordable units at the percentages set forth in subsection E of this section,

ii.

Each unit in the development, exclusive of a manager's unit or units, is affordable to, and occupied by, either a lower or very low income household.

The number and type of required replacement units shall be determined as follows:

For a development containing any occupied dwelling units, the development must contain at least the same number of replacement dwelling units, of equivalent size and bedrooms, and must be made affordable to and occupied by persons and families in the same or a lower income category as the occupied dwelling units. For unoccupied dwelling units in the development, the replacement dwelling units shall be made affordable to and occupied by persons and families in the same or lower income category as the last household in occupancy. If the income category of the last household is unknown, it is presumed, unless proven otherwise, that the dwelling units were occupied by lower income renter households in the same proportion of lower income renter households to all renter households within Riverside/San Bernardino Counties as determined by the California Department of Housing and Community Development, and replacement dwelling units shall be provided in that same percentage.

If all of the dwelling units are vacant or have been demolished within the five years preceding the application, the development must contain at least the same number of replacement dwelling units, of equivalent size and bedrooms, as existed at the high point of those units in the five-year period preceding the application, and must be made affordable to and occupied by persons and families in the same or a lower income category as those in occupancy at that same time. If the income categories are unknown for the high point, it is presumed, unless proven otherwise, that the dwelling units were occupied by very low income and low income renter households in the same proportion of very low income and low income renter households to all renter households within Riverside/San Bernardino Counties as determined by the California Department of Housing and Community Development, and replacement dwelling units shall be provided in that same percentage.

Definitions. For the purpose of this section, the following definitions shall apply unless the context clearly indicates or requires a different meaning.

"Approving authority"

is as defined in the Moreno Valley Municipal Code Title 9, Zoning Section 9.02.030.

"Child care facility"

is defined as a child day care facility other than a family day care home, including, but not limited to, infant centers, preschools, extended day care facilities, and school-age child care centers.

"Density bonus"

is defined as an increase in density over the otherwise maximum allowable residential density under the applicable general plan designation as of the date of filing of an application for density bonus with the city or, if elected by the applicant, a lesser percentage of density increase. A density bonus request shall be considered as a component of a qualified housing development.

"Development standard"

includes a site or construction condition, including, but not limited to, a height limitation, a setback requirement, a floor area ratio, an on-site open-space requirement, a minimum lot area per unit requirement, or a parking ratio that applies to a residential development pursuant to any ordinance, general plan element, specific plan, charter, or other local condition, law, policy, resolution, or regulation that is adopted by the local government or that is enacted by the local government's electorate exercising its local initiative or referendum power, whether that power is derived from the California Constitution, statute, or the charter or ordinances of the local government.

"Housing development"

is defined as a development project for five or more residential units, including mixed-use developments, constructed within a parcel. For the purposes of this section, "housing development" also includes a subdivision or common interest development as defined in Section 4100 of the Civil Code and consists of residential units or unimproved residential lots. A density bonus shall be permitted in geographic areas of the housing development other than the areas where the affordable units are located, so long as the density bonus units are located on the same parcel.

"Incentive"

is defined as a reduction in site development standards or a modification of zoning code requirements or architectural design requirements that exceed the minimum building standards approved by the California Building Standards Commission. An incentive can be requested by the applicant for purposes of reducing the cost of development to make the project financially feasible. The term "incentive" includes the term "concession" as that term is used in California Government Code Sections 65915 through 65918.

"Located within one-half mile of a major transit stop"

means that any point on a proposed development, for which an applicant seeks a density bonus, other incentives or concessions, waivers or reductions of development standards, or a vehicular parking ratio pursuant to this section, is within one-half mile of any point on the property on which a major transit stop is located, including any parking lot owned by the transit authority or other local agency operating the major transit stop.

"Lower income"

is defined as less than 80% of the area median income, as defined by Section 50079.5 of the California Health and Safety Code.

"Lower income unit"

is defined as a unit with an affordable rent or payment that does not exceed 30% of 60% of area median income adjusted for family size appropriate for the unit.

"Major transit stop"

is defined as a site containing any of the following: (a) an existing rail or bus rapid transit station; (b) a ferry terminal served by either a bus or rail transit service; or (c) the intersection of two or more major bus routes with a frequency of service interval of 20 minutes or less during the morning and afternoon peak commute periods.

"Maximum allowable residential density" or "base density"

means the greatest number of units allowed under the zoning ordinance, specific plan, or land use element of the general plan, or, if a range of density is permitted, means the greatest number of units allowed by the specific zoning range, specific plan, or land use element of the general plan applicable to the project. Density shall be determined using dwelling units per acre. However, if the applicable zoning ordinance, specific plan, or land use element of the general plan does not provide a dwelling-units-per-acre standard for density, then the local agency shall calculate the number of units by:

Estimating the realistic development capacity of the site based on the objective development standards applicable to the project, including, but not limited to, floor area ratio, site coverage, maximum building height and number of stories, building setbacks and stepbacks, public and private open-space requirements, minimum percentage or square footage of any nonresidential component, and parking requirements, unless not required for the base project. Parking requirements shall include considerations regarding number of spaces, location, design, type, and circulation. A developer may provide a base density study and the local agency shall accept it, provided that it includes all applicable objective development standards;

Maintaining the same average unit size and other project details relevant to the base density study, excepting those that may be modified by waiver or concession to accommodate the bonus units, in the proposed project as in the study.

"Moderate income"

is defined as less than 120% of the area median income, as defined in Section 50093 of the California Health and Safety Code.

"Moderate income unit"

is defined as a unit with an affordable rent or payment that does not exceed 35% of 120% of area median income adjusted for family size appropriate for the unit.

"Natural or constructed impediments"

include, but are not limited to, freeways, rivers, mountains, and bodies of water, but do not include residential structures, shopping centers, parking lots, or rails used for transit.

"Student housing development"

is defined as a development that contains bedrooms with two or more bedspaces that have a shared or private bathroom, access to a shared or private living room and laundry facilities, and access to a shared or private kitchen.

"Unobstructed access to a major transit stop"

means a resident is able to access the major transit stop without encountering natural or constructed impediments.

"Very low income"

is defined as less than 50% of the area median income, as defined in Section 50105 of the California Health and Safety Code.

"Very low income unit"

is defined as a unit with an affordable rent or payment that does not exceed 30% of 50% of the area median income, adjusted for family size appropriate for the unit.

Interpretation. If any portion of this section conflicts with State Density Bonus Law or other applicable state law, state law shall supersede this section. Any ambiguities in this section shall be interpreted to be consistent with State Density Bonus Law.

(Ord. 547 § 1.2, 1999; Ord. 984 § 3, 2022; Ord. 999 § 5, 2023; Ord. 1013, 6/25/2024; Ord. 1028, 6/17/2025)

§ 9.03.055 Density bonus program for green building and energy efficiency.

Purpose and Intent. The purpose of this section is to provide an incentive for residential housing units that are constructed to green building standards that exceed the requirements of the city's building code, which is a greenhouse gas reduction measure included in the city's Energy Efficiency and Climate Action Strategy.

Applicability. Developers of multifamily residential housing dwelling units in the R10, R15, R20, R30, MUN, MUC, MUI, H-OC, COMU, DC, and SP204-Village Residential zone on sites of at least one acre minimum.

Incentive. Developers may request a density bonus of five percent above the calculated number of units for qualified projects.

Energy Efficiency Requirements. A project must meet the applicability requirement in subsection B. For projects that meet the applicability requirement, the developer may request the incentive in subsection C if the project complies with the United States Green Building Council (USGBC) Leadership in Energy and Environmental Design (LEED) certification criteria for LEED "Certified" level or higher, or an equivalent green building rating system as approved by the community development director. LEED Certified level represents the minimum level of certification under the USGBC Leadership Energy and Environmental Design rating system, and shall be consistent with the USGBC published criteria on the date the project application to the city is deemed complete.

Implementation.

The total number of dwelling units allowed under a density bonus shall be calculated by multiplying the maximum density allowed under the applicable zoning designation (i.e., the maximum density listed in Table 9.03.040-6 of this title or the applicable specific plan designation), and multiplying the result by 1.05, for a five percent density bonus. If the result, including the density bonus, contains a fraction of a unit, the number of allowable units shall be determined by rounding down to the nearest whole number if the fraction is below one-half. Calculations containing fractions of one-half or above shall be rounded up.

This density bonus shall not be cumulative with any other density bonus program included in this section.

The development standards for density bonus projects shall be those of the applicable zoning classification.

(Ord. 910 § 5, 2016; Ord. 1005, 12/19/2023)

§ 9.03.060 Planned unit developments.

Purposes. The purposes of this section are to encourage:

Greater innovation in housing development and diversity of housing choices than would otherwise be possible according to the strict application of the site development regulations contained in this title;

Conservation or provision of more natural resources, more open space, more cultural resources, more on-site recreational facilities or more attractive freeway boundary conditions than would otherwise be possible according to the strict application of the site development regulations contained in this title;

Installation of stormwater pollution control systems pursuant to an applicable municipal stormwater permit issued by the Regional Water Quality Control Board;

Well-designed mixed-use developments, where such developments are allowed by the zoning regulations; and

Development under the density bonus program for affordable housing pursuant to Section 9.03.050.

Applicability. This section is applicable to residential developments as well as mixed-use developments where a mix of residential and nonresidential uses is allowed by the zoning regulations. This section shall only apply where warranted to advance one or more of the purposes listed in subsection A. This section shall not apply where the proposed deviations from the established site development standards would be inconsistent with the general plan or any applicable specific plan.

Review Process. Each planned unit development shall be subject to a conditional use permit. The appropriate land division application shall be filed concurrently if the land is to be divided.

Official Zoning Atlas. Each planned unit development shall be identified on the official zoning atlas as soon as practical after recordation of any associated final map, or as soon as practical after building final if there is no associated final map.

Minimum Project Area. The minimum area for a planned unit development shall be one acre.

Permitted Uses and Density. Only those uses permitted within the applicable zoning district shall be allowed within any planned unit development. The average density of any planned unit development shall not exceed the number of dwelling units per acre allowed under the applicable zoning district regulations.

Deviations from Site Development Standards. Planned unit developments may deviate from the site development standards set forth in the applicable zoning district regarding lot area, lot dimensions, lot coverage, setbacks and building height. Any such deviation(s) shall be to the minimum degree necessary to achieve one or more of the purposes listed in subsection A.

Conditions of Approval. The project conditions of approval shall establish the design of the planned unit development, including, but not limited to, the following:

The minimum lot area and lot dimensions. Flag lots are discouraged;

The maximum floor area covered by buildings;

The minimum front, side and rear setbacks. The setbacks around the exterior of the planned unit development shall be compatible with any adjacent residential developments;

The height, size, location and design of all proposed buildings, common areas, walls and other improvements; and

The method of maintaining all common areas and improvements.

(Ord. 604 § 2.5, 2002)

§ 9.03.065 Density bonus program for SB330.

Purpose and Intent. Concurrent with the approval of any change in zone from a residential use to a less intensive nonresidential use (or other land use entitlement which will reduce housing capacity), a density bonus in the amount of 1.3 units for land currently zoned R10, R15, R20, or R30 shall be assigned up to the amount of residential units impacted by the change in zone from a residential use to a less intensive nonresidential use (or other land use entitlement which will reduce housing capacity). This density bonus shall be available to applicants with a planning application for new residential development after the effective date of this section who desire to develop land currently zoned R10, R15, R20, or R30 after the date of approval of the zone change resulting in a less intensive, nonresidential development (or other land use entitlement which will reduce housing capacity).

Authority. Authority for approval of a density bonus under the provisions of this section shall be vested with the planning commission.

Applicability. This density bonus shall be available to developers of multifamily residential housing dwelling units in the R10, R15, R20, and R30 land use districts on properties of at least one-acre minimum.

Incentive. Developers may request a density bonus of 30% above the allowable number of units for up to the amount of residential units that have been impacted by the change in zone from a residential use to a less intensive nonresidential use (or other land use entitlement which will reduce housing capacity).

Implementation.

An ordinance for the adoption of a change in zone from a residential use to a less intensive nonresidential use (or other land use entitlement which will reduce housing capacity), shall include a determination establishing the existing residential capacity and identifying that these dwelling units will be made available for a residential density bonus pursuant to this section.

The total number of dwelling units allowed under this density bonus shall be calculated by multiplying the maximum density allowed under the applicable zoning designation (i.e., the maximum density listed in Table 9.03.040-6 of this title or the applicable specific plan designation), and multiplying the result by 1.3, for a 30% density bonus up to the amount of residential units impacted by the change in zone from a residential use to a less intensive nonresidential use (or other land use entitlement which will reduce housing capacity). If the result, including the density bonus, contains a fraction of a unit, the number of allowable units shall be determined by rounding down to the nearest whole number if the fraction is below one-half. Calculations containing fractions of one-half or above shall be rounded up.

This density bonus may be combined with other density bonus programs included in this chapter but the total density bonus shall not exceed 100%.

The development standards for density bonus projects shall be those of the applicable zoning classification.

The city's planning division shall publish the available number of units on the planning division's page on the city's website.

(Ord. 965 § 4, 2020)

§ 9.03.070 Streamlined ministerial approval process (Senate Bill 423, formerly SB 35).

Purpose and Intent. This section is adopted pursuant to the provisions of Senate Bill 423 (SB 423), to the extent permissible by law, to establish a streamlined ministerial review and public oversight process for the final review and approval of SB 35 applications pursuant to the requirements in California Government Code Section 65913.4. SB 423 has been designed to help address the state's continuing housing crisis. (SB 423 has extended the sunset date of SB 35 to January 1, 2036)

Applicability. This section establishes clear eligibility criteria to establish a streamlined ministerial review and public oversight process for the Planning Commission's final review and approval of SB 423 applications pursuant to the requirements in California Government Code Section 65913.4.

Qualifying Requirements.

A developer may submit an application for a development that is subject to the streamlined, ministerial approval process provided by SB 423 and not subject to a conditional use permit or any other discretionary local government review or approval.

The project must be a multifamily housing development project, as defined in California Government Code Section 65589.5, that contains at least two residential units and complies with the minimum and maximum residential density range permitted for the site per the Land Use and Community Character Element of the MoVal 2040 General Plan, plus any applicable density bonus.

Affordability Requirement. If more than 10 residential units are proposed, at least 10% of the project's total units must be dedicated as affordable to households making below 80% of the county of Riverside median income. If the project will contain subsidized units, the applicant has recorded, or is required by law to record, a land use restriction for the following minimum durations, as applicable:

55 years for rental units.

45 years for homeownership units.

The development proponent shall commit to record a covenant or restriction dedicating the required minimum percentage of units to below-market housing before issuing the first building permit.

The project must be located on a legal parcel or parcels within the incorporated city limits. At least 75% of the site's perimeter must adjoin parcels developed with urban uses.

The project must be located on a site that satisfies any of the following:

The site is zoned for residential use or residential mixed-use development.

The site has a general plan designation that allows residential use or a mix of residential and nonresidential uses.

The site is zoned for office or retail commercial use and meets the requirements of California Government Code Section 65852.24.

At least two-thirds of the square footage of the development is designated for residential use. Additional density, floor area, and units, and any other concession, incentive, or waiver of development standards granted pursuant to the Density Bonus Law in Section 65915 shall be included in the square footage calculation. The square footage of the development shall not include underground space, such as basements or underground parking garages.

The project must meet all objective zoning and design review standards in effect at the time the application is submitted.

If the project is consistent with the minimum and maximum density range allowed within the General Plan land use designation, it is deemed consistent with housing density standards.

Any density bonus, concessions, incentives, or waivers of development standards or reduction of parking standards requested under Section 9.03.050 (Density bonus program for affordable housing) are deemed consistent with objective standards.

Prevailing Wages. If the development is not in its entirety a public work, as defined in Government Code Section 65913.4(a)(8)(A), all construction workers employed in the execution of the development must be paid at least the general prevailing rate of per diem wages for the type of work and geographic area.

Skilled and Trained Workforce Provisions. A skilled and trained workforce, as defined in Government Code Section 65913.4(a)(8)(B)iii, must complete the development if the project consists of 50 or more units.

10.

The development did not or does not involve a subdivision of a parcel that is subject to the California Subdivision Map Act unless the development either: (i) receives a low-income housing tax credit and is subject to the requirement that prevailing wages be paid; or (ii) is subject to the requirements to pay prevailing wages and to use a skilled and trained workforce.

11.

The development must be located on a property that is not within a coastal zone, prime farmland, wetlands, hazardous waste site, a delineated earthquake fault zone, a flood plain, a floodway, a community conservation plan area, a habitat for protected species, or under a conservation easement.

12.

Projects may be located within a high or very high fire hazard severity zone as indicated on maps adopted by the California Department of Forestry and Fire Protection (CAL FIRE). However, within a very high fire severity zone and the statutorily defined state responsibility area, the local jurisdiction must have adopted specified fire hazard mitigation measures applicable to the site for a project to be eligible for the streamlined ministerial process.

13.

The project does not demolish any housing units that tenants have occupied in the last 10 years; are subject to any form of rent or price control, or are subject to a recorded covenant, ordinance, or law that restricts rents to levels affordable to persons and families of moderate, low, or very low incomes.

14.

The project does not demolish a historic structure that has been placed on a national, state, or local historic register.

Application and Processing. Development projects submitted pursuant to California Government Code Section 65913.4 shall be reviewed in accordance with the procedures set forth in Subsection (b) of Section 65913.4, as such procedures may be amended from time to time and as further outlined in this chapter.

The development proponent shall submit to the local government a notice of its intent to submit an application. The notice of intent (NOI) shall be in the form of an SB 423 Preliminary Application that includes all of the information described in Section 65941.1.

Scoping Consultation. Upon receipt of a notice of intent, the city will engage in a scoping consultation with any California Native American tribe traditionally and culturally affiliated with the geographic area, according to the timelines and procedures established by state law. After concluding the scoping consultation, the applicant will be notified as follows:

If it is either determined that no potential tribal cultural resource could be affected by the proposed development or if all parties and the property owner enter into an agreement establishing the methods, measures, and conditions for treatment of the tribal cultural resource, the applicant may submit an application for review.

If it is determined that a potential tribal cultural resource could be affected by the proposed development, and all parties or the property owner do not reach an agreement on methods, measures, and conditions to avoid or address impacts to tribal cultural resources, the development shall not be eligible for the streamlined, ministerial approval process.

Review of Applications. After the scoping consultation is deemed to be concluded, and if the project is eligible, the applicant may submit an application for review pursuant to Chapter 9.02, Permits and Approvals, for initial determination whether the project meets the remaining criteria for approval in compliance with Government Code Section 65913.4.

If the development is in a moderate resource area, low resource area, or an area of high segregation and poverty, as determined by the most recent "CTCAC/HCD Opportunity Map" published by the California Tax Credit Allocation Committee, a public meeting is required to be held within 45 days of receiving a notice of intent before the applicant submits an application for the proposed development. The public meeting must be held at a regular city council, subject to the Brown Act.

Once an application is submitted, the process set forth in subsections E through H below shall be followed.

Community Development Director Determinations.

The community development director shall review the application submitted hereunder and determine if the project is consistent with or conflicts with any of the objective zoning standards, objective subdivision standards, and objective design review standards applicable to the project. The community development director's review of the project shall be completed within 60 days of application submittal for projects of 150 or fewer units and 90 days for projects consisting of more than 150 units.

If the city provides written comments as to any conflicts in the objective standards, or requests additional information to make such a determination, then the 60- or 90-day timeline will restart upon submittal of a revised development application in response to such written notice. The city's written comments shall specify the standard or standards with which the development conflicts and shall provide an explanation for the reason or reasons the development conflicts with that standard or standards within the timeframe specified.

If the application can be brought into compliance with minor changes to the proposal, the city, in lieu of making detailed findings, will allow the applicant to correct any deficiencies within the timeframes noted in subsection E.2 above.

If the city fails to provide the required documentation determining consistency within these timeframes, the development shall be deemed to satisfy the city's objective planning standards and shall be deemed consistent.

The community development director's determination shall be forwarded to the city's planning commission consideration as part of the ministerial design review/public oversight process as provided for in subsection F below, under California Government Code Section 65913.4(d).

Planning Commission Ministerial Design Review/Public Oversight. The planning commission, at a noticed public meeting, shall undertake ministerial design review and public oversight as provided for in California Government Code Section 65913.4(d). Planning commission review shall include a review of the community development director's determination as outlined in subsection E above. Furthermore, the planning commission's review under this process shall be objective and strictly focused on the project's compliance with the criteria required for a streamlined project pursuant to the California Government Code Section 65913.4 and consistency with city reasonable objective zoning standards, objective subdivision standards, and objective design review standards applicable to the project, which have been adopted prior to the submittal of the application to the city and apply to other developments within the city.

The Planning Commission's review and a final determination on whether an application complies with the criteria under California Government Code Section 65913.4 and the reasonable objective zoning standards, objective subdivision standards, and objective design review standards applicable to the project must be completed in 90 days for projects with 150 or fewer units and 180 days for projects with more than 150 units, measured from the date of the application submittal.

The Planning Commission's ministerial review and public oversight process shall not in any way inhibit, chill, or preclude the ministerial approval of the project if it is in compliance with criteria specified in Government Code Section 65913.4 and consistent with the objective zoning standards, objective subdivision standards, and objective design review standards applicable to the project.

Submission of Application and Payment of Fees. Development projects submitted pursuant to California Government Code Section 65913.4 must include a copy of the city's City SB 423 Checklist Application as well as required documents for a plot plan application. Payment of application fees are due at time of submittal.

Public Hearing. The public hearing on an application hereunder shall be scheduled within the time frames provided for in subsection F above.

Modification. An applicant can request modification of approval after ministerial review and approval but prior to issuance of a final building permit pursuant to California Government Code Section 65914.3, subsection (g). If the modification request falls within the parameters in Section 65913.4, subsection (g)(3)(A) or (B)1, then such modification shall be subject to review pursuant to subsections E through H above. Otherwise, the modification shall be reviewed by the community development director to confirm compliance with California Government Code Section 65913.4.

Parking. A qualifying SB 423 project is required to provide one parking space per residential unit. Furthermore, the city shall not impose any parking requirements for qualifying projects if any of the following instances are present:

The development is located within one-half mile of the transit.

The development is located within an architecturally and historically significant historic district.

When on-street parking permits are required but not offered to the development's occupants.

When there is a car share vehicle located within one block of the development. A block can be up to 1,000 linear feet of pedestrian travel along a public street from the development.

Mixed-use projects must provide parking for the commercial component of the development as required by Section 9.11.040 (Off-street parking requirements).

The expiration dates for projects approved under SB 35 are as follows [Gov't Code Section 65913.4(f)(2)]:

No Expiration. Projects where 50% of the units are affordable to households making below 80% of the area median income (below moderate-income levels) and the project includes public investment in housing affordability beyond tax credits.

After Three Years. Projects not including affordable housing are noted in the bullet above. Projects shall remain valid for three years and stay in effect as long as construction has begun and not ceased for more than 180 days. A one-year extension to the original three-year period may be granted if progress is made toward construction.

Definitions. For the purpose of this section, the following definitions shall apply unless the context clearly indicates or requires a different meaning.

"Application"

means a submission requesting Streamlined Ministerial Approval pursuant to Government Code Section 65913.4 and the Guidelines, which contain information pursuant to Section 300(b) describing the development's compliance with the criteria outlined in Article IV of the Guidelines.

"Guidelines"

shall mean the Updated Streamlined Ministerial Approval Process issued by the California Department of Housing and Community Development, as updated March 30, 2021, and as may be updated in the future.

"Ministerial approval"

means approval of a project that complies with requirements and guidelines as set forth in Government Code Section 65913.4 that is non-discretionary and cannot require a conditional use permit or other discretionary local government review or approval.

"Ministerial processing"

means a process for development approval involving little or no personal judgment by the public official as to the wisdom or manner of carrying out the project. The public official merely ensures that the proposed development meets all the "objective zoning standards," "objective subdivision standards," and "objective design review standards" in effect at the time that the application is submitted to the local government but uses no special discretion or judgment in reaching a decision.

"Objective zoning standard", "objective subdivision standard", and "objective design review standard"

means standards that involve no personal or subjective judgment by a public official and are uniformly verifiable by reference to an external and uniform benchmark or criterion available and knowable by both the applicant or development proponent and the public official prior to submittal, and includes only such standards as are published and adopted by ordinance or resolution by a local jurisdiction before submission of a development application.

"Urban uses"

means any current or former residential, commercial, public institutional, transit or transportation passenger facility, or retail use, or any combination of those uses. Parcels that are only separated by a street or highway shall be considered adjoined.

(Ord. 1005, 12/19/2023; Ord. 1028, 6/17/2025)

§ 9.03.080 Streamlined ministerial approval process (Senate Bills 330 and 8).

Purpose and Intent. This section is adopted pursuant to the provisions of Senate Bill 330 (SB 330), Housing Crisis Act of 2019 (HCA), and Senate Bill (SB 8), which is an extension of the HCA. The HCA aims to increase residential unit development, protect existing housing inventory, and expedite permit processing.

Applicability. This section establishes clear eligibility criteria to establish a streamlined review and approval of SB 330 applications pursuant to the requirements in California Government Code Sections 65589.5, 65905.5, 65913.10, 65940, 65941.1, 65943, 65950, 66300, and 66301.

Qualifying Requirements.

The project must be a housing development project, as defined in California Government Code Section 65589.5(h)(2)(B). Specifically, pursuant to Government Code Section 65589.5(h)(2)(B) a project is a housing development project if:

Residential projects, excluding hotels, assisted living or other commercial dwelling units. Single-family, ADUs and/or JADUs are excluded from dwelling unit count;

Mixed-use development consisting of residential and nonresidential uses with at least two-thirds of the square footage of the project designated for residential use (not including hotels, assisted living or other commercial dwelling units); or

The project is a transitional or supportive housing development project.

The HCA does not apply to housing development projects located within a very high fire hazard severity zone.

The project must meet all objective zoning and design review standards in effect at the time the application is submitted.

If the project is consistent with the minimum and maximum density range allowed within the General Plan land use designation, it is deemed consistent with housing density standards.

The city may not approve a housing development project that requires the demolition or removal of a protected unit before January 1, 2030, unless the project will replace any existing, demolished or removed protected units. "Protected units" are defined as:

Affordable units deed-restricted to households earning below 80% of area median income (AMI).

Occupied by low-income households earning below 80% of AMI.

Units vacated under the Ellis Act within 10 years prior to development application.

Application and Processing.

Project applicants choosing to seek vesting rights through a SB 330 Preliminary Application are encouraged to schedule a preliminary project discussion with planning division staff to assess eligibility before submitting a Preliminary Application for the SB 330 review process.

The SB 330 Preliminary Application must be filed with the planning division prior to filing a project application requesting approval of any discretionary action.

In order for a housing development project to receive initial vesting rights, a preliminary application must include all of the information required on the SB 330 Preliminary Application consistent with subdivision (a) of California Government Code Section 65941.1 and upon verification that the preliminary application processing fee is paid.

The SB 330 Preliminary Application shall be accompanied by any maps and supporting documents, including a site plan, floor plans, elevations, exterior material details and colors, and any other drawings that are required by this application.

A subsequent project application filed with the planning division requesting approval of a discretionary action (not including ministerial administrative reviews) must be filed within 180 days of the date that the SB 330 Preliminary Application is deemed complete.

If the project application is deemed incomplete or inconsistent after filing, the city shall provide the applicant in writing with a detailed explanation of the reason within 30 days (if 150 units or fewer) or 60 days (if 151 units or more). The applicant must submit all missing or incomplete items to the planning division within 90 days of being notified in writing by planning division staff. If the project is again determined to be incomplete, the project applicant may appeal. The city has 60 days to respond to appeal.

Construction of the project must commence within two and one-half years following the date that the project receives final approval, including all necessary approvals to be eligible to apply for, and obtain a building permit or permits and all appeal periods or statutes of limitations have been exhausted or resolved in favor of the housing development project.

Any change in the residential unit count is limited to less than 20% exclusive of any increase resulting from the receipt of a density bonus, concession, waiver, or similar provision-indicated on the submitted and deemed complete SB 330 Preliminary Application, otherwise the project must be resubmitted.

Any change in the building area is limited to less than 20% exclusive of any increase resulting from receiving a density bonus, concession, waiver, or similar provision indicated on the submitted and deemed-complete SB 330 Preliminary Application, otherwise the project must be resubmitted.

10.

If the project submitted for a building permit differs substantially from the original submission (more than 20% in unit count or square footage), the planning division will re-certify the project for eligibility and re-review the project's design, restarting the timeline and requiring resubmittal of the SB 330 Preliminary Application.

Public Hearings. SB 330 prevents jurisdictions from conducting more than five public hearings in connection with the approval of a housing development project that meets objective zoning standards. The definition of "hearing" found in California Government Code Section 65905.5 includes required planning commission, city council, or other board, committee, or commission hearing or public workshop as well as any appeal hearing.

Meetings held solely pursuant to CEQA law, including CEQA appeals, are not counted toward the number of hearings.

(Ord. 1005, 12/19/2023)

§ 9.03.090 Streamlined ministerial process for parcel maps, Senate Bill 684.

Purpose and Intent. This section is adopted pursuant to the provisions of Senate Bill 684 (SB 684), to the extent permissible by law, to establish a streamlined ministerial review and public oversight process for the final review and approval of SB 684 applications pursuant to the requirements in California Government Code Sections 65852.28, 64913.4.5, and 66499.41. SB 684 has been designed to help address the state's continuing housing crisis.

Applicability. This section establishes clear eligibility criteria to establish a streamlined ministerial review and approval of SB 684 applications pursuant to the requirements in California Government Code Sections 65852.28, 64913.4.5, and 66499.41.

Qualifying Requirements. A development proponent may submit a parcel map or a tentative map application to be ministerially considered for a housing development project pursuant to California Government Code Section 66499.41 and meets the requirements of this section. The requirements of Government Code Section 66499.41 are as follows:

The proposed subdivision will result in 10 or fewer parcels and the housing development project on the lot proposed to be subdivided will contain 10 or fewer residential units. Accessory dwelling units shall not count as residential units for the purposes of this section.

The lot proposed to be subdivided meets all of the following requirements:

The lot is one of the following:

Zoned to allow multifamily residential dwelling uses, is no larger than five acres, and is substantially surrounded by qualified urban uses.

ii.

Vacant and zoned for single-family residential development, is no larger than one and one-half acres, and is substantially surrounded by qualified urban uses.

(A)

For the purposes of this section the following definitions apply,

(1)

"Vacant" means having no permanent structure, unless the permanent structure is abandoned and uninhabitable. All of the following types of housing shall not be defined as "vacant":

(a)

Housing that is subject to a recorded covenant, ordinance, or law that restricts rent or sales price to levels affordable to persons and families of low, very low, or extremely low income.

(b)

Housing that is subject to any form of rent or sales price control through a local public entity's valid exercise of its police power.

(c)

Housing occupied by tenants within the five years preceding the date of the application, including housing that has been demolished or that tenants have vacated prior to the submission of the application for a development permit.

(2)

"Qualified urban use" has the same meaning as defined in Section 21072 of the Public Resources Code.

(3)

"Substantially surrounded" has the same meaning as defined in paragraph (2) of subdivision (a) of Section 21159.25 of the Public Resources Code.

The lot is a legal parcel located within one of the following:

An incorporated city, the boundaries of which include some portion of an urbanized area.

ii.

An urbanized area or urban cluster in a county with a population greater than 600,000 based on the most recent United States Census Bureau data.

iii.

For purposes of this subparagraph, the following definitions apply:

(A)

"Urbanized area" means an urbanized area designated by the United States Census Bureau, as published in the Federal Register, Volume 77, Number 59, on March 27, 2012.

(B)

"Urban cluster" means an urbanized area designated by the United States Census Bureau, as published in the Federal Register, Volume 77, Number 59, on March 27, 2012.

The lot was not established pursuant to this section or Section 66411.7.

Except as otherwise specified, the newly created parcels are no smaller than 600 square feet.

If the parcels are zoned for single-family residential use, the newly created parcels are no smaller 1,200 square feet.

The housing units on the lot proposed to be subdivided are one of the following:

Constructed on fee simple ownership lots.

Part of a common interest development.

Part of a housing cooperative, as defined in Section 817 of the Civil Code.

Constructed on land owned by a community land trust. For the purposes of this subparagraph, "community land trust" means a nonprofit corporation organized pursuant to Section 501(c)(3) of the Internal Revenue Code that satisfies the following:

Has as its primary purposes the creation and maintenance of permanently affordable single-family or multifamily residences.

ii.

All dwellings and units located on the land owned by the nonprofit corporation are sold to qualified owners to be occupied as the qualified owner's primary residence or rented to persons and families of low or moderate income. For the purpose of this subparagraph, "qualified owner" means a person or family of low or moderate income, including a person or family of low or moderate income who owns a dwelling or unit collectively as a member occupant or resident shareholder of a limited-equity housing cooperative.

iii.

The land owned by the nonprofit corporation, on which a dwelling or unit sold to a qualified owner is situated, is leased by the nonprofit corporation to the qualified owner for the convenient occupation and use of that dwelling or unit for a renewable term of 99 years.

Part of tenancy in common, as described in Section 685 of the Civil Code.

The proposed development will meet one of the following, as applicable:

If the parcel is identified in the city's housing element for the current planning period that is in substantial compliance with Article 10.6 (commencing with Section 65580) of Chapter 3 of Division 1, the development will result in at least as many units as projected for that parcel in the housing element. If the parcel is identified to accommodate any portion of the city's share of the regional housing need for low or very low income households, the development will result in at least as many low or very low income units as projected in the housing element. These units shall be subject to a recorded affordability restriction of at least 45 years.

If the parcel is not identified in the city's housing element for the current planning period that is in substantial compliance with Article 10.6 (commencing with Section 65580) of Chapter 3 of Division 1, the development will result in at least 66% of the maximum allowable residential density as specified by local zoning or 66% of the applicable residential density specified in subparagraph (B) of paragraph (3) of subdivision (c) of Section 65583.2, whichever is greater.

The average total area of floorspace for the proposed housing units on the lot proposed to be subdivided does not exceed 1,750 net habitable square feet. For purposes of this paragraph, "net habitable square feet" means the finished and heated floor area fully enclosed by the inside surface of walls, windows, doors, and partitions, and having a headroom of at least six and one-half feet, including working, living, eating, cooking, sleeping, stair, hall, service, and storage areas, but excluding garages, carports, parking spaces, cellars, half-stories, and unfinished attics and basements.

The development of a housing development project on the lot proposed to be subdivided does not require the demolition or alteration of any of the following types of housing:

Housing that is subject to a recorded covenant, ordinance or law that restricts rent to levels affordable to persons and families of low, very low, or extremely low income.

Housing that is subject to any form of rent or price control through a local public entity's valid exercise of its police power.

A parcel on which an owner of residential real property has exercised the owner's rights under Chapter 12.75 (commencing with Section 7060) of Division 7 of Title 1 to withdraw accommodations from rent or lease within 15 years before the date that the development proponent submits an application.

The lot proposed to be subdivided is not located on a site that is any of the following:

Either prime farmland or farmland of statewide importance, as defined pursuant to United States Department of Agriculture land inventory and monitoring criteria, as modified for California, and designated on the maps prepared by the Farmland Mapping and Monitoring Program of the Department of Conservation, or land zoned or designated for agricultural protection or preservation by a local ballot measure that was approved by the voters of that jurisdiction.

Wetlands, as defined in the United States Fish and Wildlife Service Manual, Part 660 FW 2 (June 21, 1993).

Within a very high fire hazard severity zone, as determined by the Department of Forestry and Fire Protection pursuant to Section 51178 or within a high or very high fire hazard severity zone as indicated on maps adopted by the Department of Forestry and Fire Protection pursuant to Section 4202 of the Public Resources Code.

A hazardous waste site that is listed pursuant to Section 65962.5 or a hazardous waste site designated by the Department of Toxic Substances Control pursuant to former Section 25356 of the Health and Safety Code, unless either of the following applies:

The site is an underground storage tank site that received a uniform closure letter issued pursuant to subdivision (g) of Section 25296.10 of the Health and Safety Code based on closure criteria established by the State Water Resources Control Board for residential use or residential mixed uses. This section does not alter or change the conditions to remove a site from the list of hazardous waste sites listed pursuant to Section 65962.5.

ii.

The State Department of Public Health, State Water Resources Control Board, Department of Toxic Substances Control, or a local agency making a determination pursuant to subdivision (c) of Section 25296.10 of the Health and Safety Code, has otherwise determined that the site is suitable for residential use or residential mixed uses.

Within a delineated earthquake fault zone as determined by the State Geologist in any official maps published by the State Geologist, unless the development complies with all applicable seismic protection building code standards adopted by the California Building Standards Commission under the California Building Standards Law and by the city.

Within a special flood hazard area subject inundation by the one-percent-annual-chance flood (100-year flood) as determined by the Federal Emergency Management Agency in any official maps published by the Federal Emergency Management Agency. If a development proponent is able to satisfy all applicable federal qualifying criteria in order to provide that the site is eligible for streamlined approval under this section, a development may be located on a site described in this paragraph if either of the following is met:

The site has been subject to a Letter of Map Revision prepared by the Federal Emergency Management Agency and issued to the city.

ii.

The site meets Federal Emergency Management Agency requirements necessary to meet minimum flood plain management criteria of the National Flood Insurance Program pursuant to Part 59 (commencing with Section 59.1) and Part 60 (commencing with Section 60.1) of Subchapter B of Chapter I of Title 44 of the Code of Federal Regulations.

Within a regulatory floodway as determined by the Federal Emergency Management Agency in any official maps published by the Federal Emergency Management Agency, unless the development has received a no-rise certification in accordance with Section 60.3(d)(3) of Title 44 of the Code of Federal Regulations.

Land identified for conservation in an adopted natural community conservation plan pursuant to the Natural Community Conservation Planning Act (Chapter 10 (commencing with Section 2800) of Division 3 of the Fish and Game Code), habitat conservation plan pursuant to the Federal Endangered Species Act of 1973 or another adopted natural resource protection plan.

Habitat for protected species identified as candidate, sensitive, or species of special status by state or federal agencies, fully protected species, or species protected by the Federal Endangered Species Act of 1973, the California Endangered Species Act or the Native Plant Protection Act.

Land under conservation easement.

10.

The proposed subdivision conforms to all applicable objective requirements of the Subdivision Map Act, except as otherwise expressly provided in this section.

11.

The proposed subdivision complies with all applicable standards established pursuant to Section 65852.28.

12.

Any parcels proposed to be created pursuant to this section will be served by a public water system and a municipal sewer system.

13.

The proposed subdivision will not result in any existing dwelling unit being alienable separate from the title to any other existing dwelling unit on the lot.

Standard Applicability. A housing development project on a proposed site to be subdivided pursuant to this section is not required to comply with either of the following requirements:

A minimum requirement on the size, width, depth, frontage, or dimensions of an individual parcel created by the development beyond the minimum parcel size specified in this section.

The formation of a homeowner's association, except as required by the Davis-Stirling Common Interest Development Act. This shall not be construed to prohibit the city from requiring a mechanism for the maintenance of common space within the subdivision, including, but not limited to, a road maintenance agreement.

Application and Processing.

Project applicants choosing to pursue a subdivision/housing development project through a SB 684 Project Application are encouraged to schedule a preliminary project discussion with planning division staff to assess eligibility before submitting a Project Application for the SB 684 review process.

The city shall approve or deny an application for a parcel map or tentative map submitted pursuant to California Government Code Sections 65852.28 and 66499.41 within 60 days from the date the city receives a completed application. If the city does not approve or deny a completed application within 60 days, the application shall be deemed approved. If the city denies the application, the city shall, within 60 days from the date the city receives a completed application, return in writing a full set of comments to the applicant with a list of items that are defective or deficient and a description of how the applicant can remedy the application.

The city may deny the issuance of a parcel map, tentative map, or a final map if it makes written finding, based upon a preponderance of evidence, that the proposed housing development project would have a specific, adverse impact, as defined and determined in paragraph (2) of subdivision (d) of California Government Code Section 65589.5, upon public health and safety and for which there is no feasible method to satisfactorily mitigate or avoid the specific, adverse impact.

Through the exercise of the authority contained within California Government Code Sections 66499.41,

The city is not required to permit an accessory dwelling unit or junior accessory dwelling unit on the parcels created. If the city chooses to permit accessory dwelling units or junior accessory dwelling units, the units shall not count as residential units for the purposes of subsection C of this section.

The city is not required to permit an urban lot split on the parcels created.

The above would not apply to a site located within a single-family residential horsekeeping zone designated in a specified master plan adopted before January 1, 1994, that regulates land zoned single-family horsekeeping, commercial, commercial-recreational, and existing industrial within the plan area.

Development Standards.

Any housing development project constructed on the lot proposed to be subdivided pursuant to California Government Code Section 66499.41 shall comply with all applicable objective zoning standards, objective subdivision standards, and objective design standards as established by the city that are not inconsistent with California Government Code Sections 65852.28 and 66499.41. The city's objective standards shall not:

Physically preclude the development of a project built to densities as specified in subparagraph (B) of paragraph (3) of subdivision (c) of California Government Code Section 68823.2.

Notwithstanding the above, for a development located on a lot that meets the definition of clause (ii) of subparagraph (A) of paragraph (2) of subdivision (a) of California Government Code Section 66499.41, a local agency may impose a height limit of no less than the height allowed pursuant to the existing zoning designation applicable to the lot.

Impose any requirements that apply to a project solely or partially on the basis that the subdivision or housing development receives approval pursuant to California Government Code Sections 65852.28 and 66499.41.

Require a setback between the units, except as required in the California Building Code (Title 24 of the California Code of Regulations).

Require that parking be enclosed or covered.

Impose side and rear setbacks from the original lot line inconsistent with subparagraph (B) of paragraph (2) of subdivision (b) of Section 65852.21.

Impose parking requirements inconsistent with paragraph (1) of subdivision (c) of Section 65852.21.

For a housing development project consisting of three to seven units, impose a floor area ratio standard that is less than 1.0.

For a housing development project consisting of eight to 10 units, impose a floor area ratio standard that is less than 1.25.

Building Permit.

The city shall issue a building permit for one or more residential units that are part of a housing development project consisting of 10 or fewer units on a lot proposed to be subdivided as a part of a subdivision pursuant to California Government Code Sections 65852.28 and 66499.41, if the applicant for the permit has met both of the following requirements:

The applicant has received a tentative map approval or parcel map approval for the subdivision.

The applicant has submitted a building permit application that the city has deemed complete.

At the time of building permit issuance, the applicant shall submit proof (to the satisfaction of the city) of a recorded covenant and agreement enforceable by the city that states that the applicant's successors and assignees agree that the building permit is issued on the condition that a certificate of occupancy or equivalent final approval for the building will not be issued unless the final map has been recorded.

The building permit shall be issued based upon the tentative map or parcel map and its conditions of approval. Any dedication, improvement, and sewer requirements identified in the approved tentative map or parcel map or its conditions of approval shall be guaranteed to the satisfaction of the city at the time the building permit is issued.

The city may require security to ensure faithful performance of the requirements identified in the approved tentative or parcel map or its conditions of approval. The amount of security shall be determined by the city and shall not be more 300% of the total estimated cost of the improvements or of the acts to be performed. The security shall be provided in either of the following forms, as determined by the city:

Bond or bonds by one more duly authorized corporate sureties.

An instrument of credit from an agency of the state, federal, or local government when any agency of the state, federal, or local government provides at least 20% of the financing for the portion of the act or agreement requiring security, or from one or more financial institutions subject to regulation by the state or federal government and pledging that the funds necessary to carry out the act or agreement are on deposit and guaranteed for payment, or a letter of credit issued by such a financial institution.

The city may deny issuance of a building permit if the building official makes a written finding, based upon a preponderance of evidence, that construction of the proposed structure or structures before recordation of the final map would have a specific, adverse impact, as defined and determined in paragraph (2) of subdivision (d) of California Government Code Section 65589.5, upon public health and safety and for which there is no feasible method to satisfactorily mitigate or avoid the specific, adverse impact.

(Ord. 1013, 6/25/2024; Ord. 1028, 6/17/2025)

Moreno Valley City Zoning Code

CHAPTER 9

03 RESIDENTIAL DISTRICTS

§ 9.03.010 Purpose and intent.

(Ord. 359, 1992)

§ 9.03.020 Residential development districts.

(Ord. 359, 1992; Ord. 468 § 1.3, 1995; Ord. 547 § 1.1, 1999; Ord. 726 § 4.2, 2006; Ord. 797 § 2.2, 2009)

§ 9.03.030 Use regulations for residential districts.

(Ord. 359, 1992; Ord. 520 § 1.8, 1997)

§ 9.03.040 Residential site development standards.

Rural Residential Requirements.

Slope-Density-Natural Area Table 9.03.040-4.

Slope Class	Allowable Density (DU/Acre)	Amount of Open Space Required
Greater than 25%	0.05 (1 du/20 ac)	60%
15.1% to 25%	0.10 (1 du/10 ac)	50%
10% to 15%	0.20 (1 du/5 ac)	35%
Less than 10%	0.40 (1 du/2.5 ac)	n/a

Subdivision Design and Future Land Divisions.

Building Height. Dwellings and other accessory structures shall not exceed 30 feet in overall height, provided that on slopes of less than 10%, the overall height shall not exceed 35 feet.

Lot Size	Standards
Under 40,000 s.f.	R2 district standards
40,000 s.f. or greater	R1 district standards

Grading within the rural residential district shall be performed as described under the hillside residential requirements, subsection (B)(6) of this section.

Hillside Residential Requirements.

Slope-Density-Natural Area Table 9.03.040-5.

Slope Class	Allowable Density (DU/Acre)	Minimum Amount of Open Space Required
Greater than 25%	0.10 (1 du/10 ac)	60%
15.1% to 25%	0.25 (1 du/4 ac)	50%
10% to 15%	0.50 (1 du/2 ac)	35%
Less than 10%	1.00 (1 du/ac)	n/a

The total number of dwelling units permitted within a project area shall be the sum of the allowable dwelling units within each slope class. For example, if 10 acres of the project falls within the 15.1% to 25% slope class and five acres falls within the greater than 25% slope class, then the total permitted yield shall be three dwelling units (10 ac x 0.25 du/ac plus 5 ac x 0.10 du/ac).

Subdivision Design and Future Land Divisions.

Building Height. Dwellings and other accessory structures shall not exceed 30 feet in overall height, provided that on slopes of less than 10%, the overall height shall not exceed 35 feet.

Lot Size	Standards
Less than 20,000 s.f.	R-3 district standards
20,000 s.f. to 40,000 s.f.	R-2 district standards
40,000 s.f. or greater	R-1 district standards

Slope Class	Standards
15.1—25%	Padded building sites may be allowed, but maximum use of custom foundations and split level designs shall be employed to reduce the need for large, padded building areas.
Above 25%	Mass grading is not permitted. Special hillside architectural and design techniques are expected in order to conform to the natural landform. Homes constructed on lots within this terrain shall use custom, multiple-level foundations.
For all areas	All graded areas shall be protected from wind and water erosion through acceptable slope stabilization methods such as planting, walls or jute netting.

Slope Calculations. For the purposes of this section, the following method will be used to determine slope.

Slope Mapping Method.

The percent slope of any particular piece of land shall be plotted on the map as described in this subsection.

In preparing a slope map, those portions of ravines, ridges and terraces of less area generally sloping at 25% slope or greater, shall be regarded as part of the bordering 25% slope or greater band.

Table 9.03.040-6 Residential Site Development Standards Single-Family Standards
Requirement			R1	R2	RA2	R3	R5	RS10
1.	Maximum density (DUs* per net acre)		1	2	2	3	5	10
2.	Minimum lot size (sq. ft. net area)		40K**	20K	20K	10K	7,200	4,500
3.	Minimum lot width, in feet		150	100	100	90	70	45
Cul-de-sac/knuckle lot frontage			50	50	50	50	50	45
4.	Minimum lot depth, in feet		170	120	120	100	100	85
5.	Minimum front yard setback		25	25	25	25	20	20
Front-facing garages								10
Buildings other than front-facing garages								10
6.	Minimum side yard setback, in feet***
	a.	Interior side yard	See Note 1	See Note 1	See Note 1	See Note 1	See Note 2	See Note 3
	b.	Street side yard	20	20	20	15	15	10
7.	Minimum rear yard setback, in feet***		40	35	35	30	15	15
8.	Maximum lot coverage		25%	30%	30%	40%	40%	50%
9.	Maximum building and structure height, in feet		Two stories not to exceed 35 feet.
10.	Minimum dwelling size (sq. ft.)		1500	1500	1500	1250	1250	1000
11.	Minimum distance between buildings, in feet (including main DUs and accessory structures)		20	15	15	10	10	10
12.	Floor area ratio
	a.	One-story home	0.25	0.30	0.30	0.40	0.40	0.50
	b.	Multi-story home	0.50	0.60	0.60	0.70	0.70	0.75

Notes to Residential Site Development Standards Table 9.03.040-6.
*	The term "DUs" means dwelling units.
**	The term "K" means thousands.
***	See Section 9.08.030 regarding accessory structures and room additions.
1.	Combined interior side yard setbacks of 20 feet shall be provided with a minimum of five feet on one side.
2.	Combined interior side yard setbacks of 15 feet shall be provided with a minimum of five feet on one side.
3.	In the RS10 district the minimum street side setback shall be 10 feet. The interior side setback shall be five feet, except in the case of zero lot line developments with houses placed on an interior side lot line. When a house is placed on an interior side lot line, the other minimum side yard setback shall be 10 feet. Where applicable, an easement at least five feet in width shall be provided along the common lot line. The easement shall guarantee the right to use and occupy the easement for a roof overhang(s), stormwater drainage and for building maintenance and repair.
4.	The minimum front yard setback from private streets within the R1, R2 and R3 districts shall be 55 feet measured from the center line of the street. The minimum front yard setback from private streets within the R5 district shall be 50 feet measured from the center line of said street.

Table 9.03.040-7 Residential Site Development Standards Multifamily Standards
Requirement		R10	R15	R20	R30
1.	Maximum density (DUs*/net acre)	10	15	20	30
2.	Minimum lot size (net area in sq. ft.)**	1 acre	1 acre	1 acre	1 acre
3.	Minimum lot width in ft.	200	200	200	200
4.	Minimum lot depth in ft.	175	175	175	175
5.	Minimum front yard setback, in ft.	20	25	30	30
6.	Minimum side yard setback, in ft.
	Interior side yard	10	10	10	10 ft. plus 2 ft. for every 5 ft. in height over 30 ft.
	Street side yard	20	20	20	20
7.	Minimum rear yard setback, in ft.	15	20	25	10 ft. plus 2 ft. for every 5 ft. in height over 30 ft.
8.	Maximum lot coverage	40%	45%	50%	50%
9.	Maximum building and structure height, in ft.	50 feet
10.	Minimum dwelling size (sq. ft.)	See Note 1
11.	Minimum distance between buildings, in ft. (including main DUs and accessory structures)	20	20	20	20
12.	Floor area ratio	0.75	0.75	0.75	1.0

NOTES:
*	The term "DUs" means dwelling units.
**	Minimum lot size only applies to newly subdivided multifamily lots; existing lots can be developed under the multifamily development standards.

Special Single-Family Residential Development Standards.

In the RS10 district, driveways and fire hydrants shall be designed and located to maximize on-street parking opportunities in front of each residence.

Front porches;

Automatic garage door openers;

Electronic security systems.

For all single-family residential developments in the R10, R15, R20, and R30 districts a planned unit development application shall be submitted to establish the applicable development standards.

Special Multiple-Family Residential Development Standards.

Parking for each use shall comply with the requirements of Chapter 9.11 of this title.

Table 9.03.040-8
Designation	Minimum Density*	Maximum Density
R10	8 units/acre	10 units/acre
R15	12 units/acre	15 units/acre
R20	16 units/acre	20 units/acre
R30	24 units/acre	30 units/acre

*	Eighty percent of allowable density must be achieved by all multiple-family residential developments.

General Multiple-Family Guidelines.

Opposing garages or carports should be turned to avoid the monotony of alley-like parking corridors.

Parking areas should be staggered and landscaped to add visual interest, and opportunities for accent treatments.

Parking spaces within multifamily areas shall be located within 250 feet of the dwellings they serve.

Open parking areas should be clustered and treated as landscaped plazas and courts.

Landscaping shall be used around the perimeter of the lot, as well as within the lot, reducing paved area and providing for a more pedestrian oriented site.

No more than four units for a two-story structure should be served by one entry.

Common open space at a minimum of 300 square feet per each residential dwelling in the project is required.

10.

Individual units should have a porch or porch-like space at the front door.

11.

Trash enclosures shall be located to provide a maximum walking distance of 250 feet from the units they serve.

12.

Trash enclosures shall include solid roofs and be designed to be compatible with the project's architecture.

13.

Trash enclosures shall not be located on dead end drive aisles, unless adequate turnaround is provided for collection vehicles.

14.

There shall be at least one double-bin trash enclosure for every 48 residential units.

15.

16.

17.

Freestanding structures, like gazebos or pergolas, should be located to define activity areas at pathway intersections or in secluded landscape areas.

18.

Drive aisles shall be at least 24 feet wide for two-way traffic and shall be at least 20 feet wide for one-way traffic.

19.

20.

Multiple-family projects warrant special design considerations, including:

Intimate, shaded outdoor seating areas;

A network of pathways, providing interesting walking experiences;

Gentle slopes for outdoor pathways and ramps to entry doors and between floors;

Convenient and attractive access to transit, including porte cocheres, information kiosks, seating areas and water elements;

Security;

Direct ambulance access (senior housing projects);

Parking close to units;

Elevators (senior housing projects).

21.

Multifamily units shall be clustered to minimize grading and to help maintain the natural landscape.

22.

23.

Architectural features should be used to increase privacy from nearby units and common or public spaces.

24.

25.

A diagram of the complex showing the location of the viewer and the building designations shall be positioned at each visitor entrance of a multiple-family development.

26.

Buildings shall provide for a variety of colors and architectural features to break up the massing of buildings and provide visual interest.

§ 9.03.050 Density bonus program for affordable housing.

A site plan that identifies all units in the project, including the location of the affordable units and the bonus units.

A narrative briefly describing the housing development and shall include information on:

The number of units permitted under the general plan;

Target income of affordable housing units and proposals for ensuring affordability;

The number of bonus units requested based on subsection E.3 of this section.

The actual cost reduction achieved through the incentive;

Evidence that the cost reduction allows the applicant to provide affordable units or affordable sales prices; and

Any such additional information in support of a request for a density bonus as may be requested by the community development director.

Agrees to construct and maintain at least five percent of the units dedicated to very low income households;

Agrees to construct and maintain at least 10% of the units dedicated to lower income households;

10.

Density Bonus Calculation and Allowance.

Very low income per California Government Code Section 65915(f)(2).

Lower income per California Government Code Section 65915(f)(1).

Moderate income per California Government Code Section 65915(f)(4).

Foster Youth, Disabled Veterans, and Homeless Persons. The density bonus for a housing development for transitional foster youth, disabled veterans, or homeless persons shall be 20%.

10.

Incentives Available to Housing Projects. Incentives are available to housing development are as follows:

Number of Incentives/Concessions	Very Low Income Percentage	Lower Income Percentage	Moderate Income Percentage
1	5%	10%	10%
2	10%	17%	20%
3	15%	24%	30%
4	16%	26%	45% (for sale units)
5	100% low/very low/mod (20% moderate allowed)*	100% low/very low/mod (20% moderate allowed)*	100% low/very low/mod (20% moderate allowed)*

Note:
If the project is located within one-half mile of a major transit stop, the applicant shall also receive a height increase of up to three additional stories, or 33 feet.

Available Incentives/Concessions. A qualifying project may be entitled to up to four incentives, depending on the percentage of affordable housing that will be included within the development.

A concession falls within three categories (California Government Code Section 65915(k)(1), (2) and (3)).

Reduction in the site development standards of this development code (e.g., site coverage, off-street parking requirements, reduced lot dimensions, and/or setback requirements);

Other regulatory incentives or concessions proposed by the developer or the city that will result in identifiable and actual cost reductions.

Except as otherwise provided in this subsection, the following parking requirements shall apply:

Zero to one bedroom: one on-site parking space.

Two to three bedrooms: one and one-half on-site parking spaces.

Four or more bedrooms: two and one-half on-site parking spaces.

If a housing development consists solely of rental units, exclusive of a manager's unit or units, with an affordable housing cost to lower income families, as provided in Section 50052.5 of the California Health and Safety Code, then no parking spaces shall be required as long as the development meets either of the following criteria:

The development is located within one-half mile of a major transit stop and there is unobstructed access to the major transit stop from the development; or

If a housing development consists solely of rental units, exclusive of a manager's unit or units, with an affordable housing cost to lower income families, as provided in Section 50052.5 of the California Health and Safety Code, and the development is either a special needs housing development, as defined in Section 51312 of the California Health and Safety Code, or a supportive housing development, as defined in Section 50675.14 of the California Health and Safety Code, then no parking spaces shall be required. A development that is a special needs housing development shall have either paratransit service or unobstructed access, within one-half mile, to fixed bus route service that operates at least eight times per day.

Number of Bedrooms	Required Parking Spaces per Unit,*
0 to 1 bedroom	1
2 to 3 bedrooms	1.5
4 or more bedrooms	2.5
Projects with at least 20% low-income units, or at least 11% very low income units***	0.5
100% affordable housing projects****	No requirement

NOTES:
*	If the total number of spaces required results in a fractional number, it shall be rounded up to the next whole number.
**	If a residential or mixed residential/commercial development project includes the required percentage of low, very low income, or includes a minimum 10% transitional foster youth, veteran, or homeless persons units, or provides for-rent housing for individuals who are 62 years of age or older, or is a special needs housing development and is located within one-half mile of a major transit stop where there is unobstructed access to a major transit stop from the development, then, upon the request of the developer, a parking ratio not to exceed 0.5 spaces per bedroom shall apply to the residential portion of the development.
***	Must be located within one-half mile of a major transit stop, with unobstructed access to the major transit stop from the development.
****	Must be located within one-half mile of a major transit stop, with unobstructed access to the major transit spot from the development OR for individuals 62 years of age or older and has either paratransit service or unobstructed access within one-half mile, to fixed bus route service that operates at least eight times per day.