The antenna is attached to an existing structure;

The antenna does not extend more than 10 feet above the top of the structure; and

The related equipment is not located in the right-of-way.

The antenna and associated support structure are not located within any required landscaped setbacks, front or side yard setback, or in the area located between the front setback line and the front of the building; and

The antenna and associated support structure do not extend more than 10 feet above the adjoining grade.

The antenna and support structure shall be subject to the maximum building height for the corresponding zone in which they are located as set forth in PMC § 20.20.020(9) for RS-zoned property and PMC § 20.25.020(8) for RM-zoned property; said height restriction shall not be subject to granting of a variance;

The antenna and associated support structure shall not be located within any required landscaped setback, front or side yard setback, or in the area located between the front setback line and the front of the building;

The antenna and associated structure shall comply with required building setbacks and shall be set back from the required side yard setback an additional one foot for each foot of height over 10 feet;

The antenna and associated structure shall comply with the performance standards set forth in PMC § 20.59.040; and

No more than one freestanding support structure shall be permitted per lot.

Attached accessory antenna devices, parabolic antennas two feet or less in diameter, omnidirectional antennas six feet or less in length, directional antennas five feet or less in height with a combined surface area of not more than 580 square inches as viewed from any one point, and stealth antennas, and not extending more than 15 feet above the roof surface of the structure; provided, that the related equipment is not located in the right-of-way.

Attached parabolic antennas greater than two feet in diameter, omnidirectional antennas greater than six feet in length, and directional antennas greater than five feet in height with a combined surface area of more than 580 square inches as viewed from any one point shall also comply with the following requirements:

Freestanding parabolic antennas and associated support structures shall be subject to the following criteria:

Attached accessory antenna devices, parabolic antennas two feet or less in diameter, omnidirectional antennas six feet or less in length, and directional antennas five feet or less in height with a combined surface area of not more than 580 square inches as viewed from any one point, and stealth antennas, and not extending more than 15 feet above the roof surface of the structure; provided, that the related equipment is not located in the right-of-way;

Attached parabolic antennas greater than two feet in diameter, omnidirectional antennas greater than six feet in length, directional antennas greater than five feet in height with a combined surface area of more than 580 square inches as viewed from any one point, and stealth antennas shall also comply with the following requirements:

Freestanding antennas and associated support structures shall be subject to the following criteria:

Stealth antenna;

Attachment of the proposed antennas and associated equipment to an existing structure, which does not include a monopole or freestanding facility, only when subsection (1)(a) of this section cannot be reasonably accomplished;

Attachment of the proposed antennas and associated equipment to an existing structure, which already holds one or more wireless communication facilities and may include a monopole or freestanding facility, only when subsection (1)(a) or (1)(b) of this section cannot be reasonably accomplished;

Freestanding facilities which extend no more than 15 feet above adjacent existing vegetation or structures, only when subsection (1)(a), (1)(b) or (1)(c) of this section cannot be reasonably accomplished; or

Freestanding facilities which extend more than 15 feet above adjacent existing vegetation or structures, only when subsections (1)(a) through (1)(d) of this section cannot be reasonably accomplished.

The applicant shall provide proof of inability to locate on an existing structure in the immediate vicinity due to the following:

The applicant shall provide proof of notification and an offer of opportunities for other service providers to locate on the freestanding facility. As a condition of city approval of any new freestanding transmission towers, the applicant shall comply with the following requirements:

Antennas may not extend more than 10 feet in RS and RM zones and 15 feet in all other zones above their supporting structure, monopole, lattice tower, building or other structure, or surrounding vegetation;

Site location and development shall preserve the preexisting character of the surrounding buildings, land use and the zone district to the extent possible, while maintaining the function of the communications equipment. Wireless communication facilities shall be integrated through location, siting and design to blend in with the existing characteristics of the site through application of the following measures:

Related equipment facilities used to house wireless communications equipment shall be located within buildings or placed underground when possible. When they cannot be located in buildings or placed underground, equipment shelters or cabinets shall be screened. Alternate methods for screening may include the use of building or parapet walls, sight-obscuring fencing and/or landscaping, screen walls or equipment enclosures; and

Wireless communication facilities and related equipment facilities shall be of neutral colors such as white, gray, blue, black or green, or similar in building color in the case of facilities incorporated as part of the features of a building, unless specifically required to be painted another color by a federal or state authority. Wooden poles are not required to be painted;

The application shall provide specific locational information including GIS coordinates of all proposed small cell facilities and specify whether the small cell facilities will utilize existing, replacement or new poles, towers, existing buildings and/or other structures. Ground-mounted equipment, conduit, junction boxes and fiber and electrical connections necessary for and intended for use in the deployment shall also be specified regardless of whether the additional facilities are to be constructed by the applicant or leased from a third party. Where another party is responsible for installing such electric and fiber utilities, conduit, cables, and related improvements, the applicant's construction drawings will include such utilities to the extent known at the time of application, but at a minimum the applicant must indicate how it expects to obtain fiber and electric service to the small cell facility. Detailed schematics and visual renderings of the small cell facilities, including engineering and design drawings, shall be provided by the applicant. The application shall have sufficient detail to identify:

The applicant must show written approval from the owner of any pole or structure for the installation of its small cell facilities on such pole or structure. Such written approval shall include approval of the specific pole, engineering and design standards from the pole owner, unless the pole owner is the city. Submission of the lease agreement between the owner and the applicant is not required. For city-owned poles or structures, the applicant must obtain a lease from the city prior to or concurrent with the small cell facility permit application and must submit as part of the application the information required in the lease for the city to evaluate the usage of a specific pole.

If the application is for a new pole or a replacement light pole, then the applicant must provide a photometric analysis.

The applicant can batch multiple small wireless facility sites in one application. The applicant is encouraged to batch the small wireless facility sites within an application in a contiguous service area.

Any application for a small cell facility located in the right-of-way adjacent to a parcel zoned for residential use shall demonstrate that it has considered the following:

Any application for a small cell permit which contains an element which is not exempt from SEPA review shall simultaneously apply under Chapter 43.21C RCW and Chapter 21.04 PMC. Further, any application proposing small cell facilities in shoreline management zones (pursuant to the city's shoreline management program) or in critical areas (pursuant to Chapter 21.06 PMC) must indicate that the application is exempt or comply with the review processes in such codes.

The applicant shall submit a sworn affidavit signed by an RF engineer with knowledge of the proposed project affirming that the small cell deployment will be compliant with all FCC and other governmental regulations in connection with human exposure to radio-frequency emissions for every frequency at which the small cell facility will operate. If additional transmission facilities necessary to the small cell facility, such as microwave backhaul, are to be provided by a third party, then the small cell permit shall be conditioned on an RF certification showing the cumulative impact of the RF emissions of the entire installation. The applicant may provide one emissions report for the entire small cell deployment if the applicant is using the same small cell facility configuration for all installations within that batch or may submit one emissions report for each subgroup installation identified in the batch.

The applicant shall provide proof of FCC and other regulatory approvals required to provide the service(s) or utilize the technologies sought to be installed.

A professional engineer licensed by the state of Washington shall certify in writing, over his or her seal, that the construction plans of the small cell facilities and structure or pole and foundation are designed to reasonably withstand wind and seismic loads or, in the case of a utility-owned structure, provide written confirmation that the pole will support the additional loads.

Applications filed under this title shall be numbered consecutively in the order of their filing, and shall become a part of the official records of the city. Copies of all notices, application materials, staff reports, and actions shall state the file number and be filed with the application.

Applicants shall submit a traffic control plan and information for right-of-way obstruction permit.

Recognizing that small cell facility technology is rapidly evolving, the director is authorized to adopt and publish standards for the technological and structural safety of city-owned structures and to formulate and publish application questions for use when an applicant seeks to attach to city-owned structures.

A preapplication meeting is encouraged prior to submitting an application for a small cell permit. The purpose of a preapplication meeting is to discuss the nature of the proposed deployment of the small cell network, review process and schedule, and applicable plans, policies and regulations.

The city shall make reasonable efforts to issue the small cell permit in a time period that adheres to the presumptively reasonable periods of time set by the FCC and also consistent with any conflicting provisions of state or federal law, and the preservation of the city's health, safety and aesthetic environment.

The director may approve, deny or conditionally approve all or any portion of the sites proposed in the small cell permit application. The denial of one or more small cell facility locations within a batched submission shall not be the sole basis for a denial of other locations or the entire application for small cell facilities.

Any applicant may withdraw an application at any time, provided the withdrawal is in writing and signed by all persons who signed the original application or their successors in interest. When a proper withdrawal is received, the application shall be deemed null and void. If such withdrawal occurs prior to the director's decision, then reimbursement of fees submitted in association with said application shall be prorated to withhold the amount of city costs incurred in processing the application prior to time of withdrawal. These city costs shall be based upon a determination by the director of the total hours expended in project review from the time of project application to time of withdrawal, utilizing an hourly dollar amount for staff time as established by resolution. If such withdrawal is not accomplished prior to the director's decision, there shall be no refund of all or any portion of such fee.

Any applicant may revise an application. Such revision shall be deemed to supersede the prior application documents. If such revision is significant enough to require a revised administrative review, the director may assess another application fee equal to the amount required to review that application.

Failure of an applicant to provide additional information as requested within 60 days of notice by the director shall be deemed a withdrawal of that application, unless an extension period has been approved by the director.

If the applicant includes small cell facility locations within a residential or mixed-use zone, the director shall provide notice of a complete application for a small cell permit on the city's website with a link to the small cell permit application. The notice shall include an email contact and telephone number for the applicant to answer citizen inquiries.

Review of the site locations proposed by the applicant shall be governed by the provisions of 47 USC 253 and 332 and other applicable statutes, regulations and case law. Applicants for master permits, leases and the small cell facility permits shall be treated in a competitively neutral and nondiscriminatory manner with other service providers, utilizing supporting infrastructure which is functionally equivalent, that is, service providers whose facilities are similarly situated in terms of structure, placement, or cumulative impacts. Small cell facility permit review under this chapter shall neither prohibit nor have the effect of prohibiting the ability of an applicant to provide telecommunications services.

The director shall use the criteria listed below when deciding upon the application. In addition, the director may approve the application only if:

The director shall approve, approve with conditions or modifications, or deny an application. The director shall include any conditions to ensure consistency with city zoning and utility regulations, and may include mitigation measures proposed under SEPA, if applicable. The applicant carries the burden of proof that a preponderance of the evidence supports approval of the application or approval with conditions or modifications.

Administrative review decisions (and any reconsideration of that decision) and SEPA threshold determinations are final decisions, effective on the day issued. The director's decision is the city's final decision on the application and is not subject to administrative appeals.

Appeal to Superior Court. A final decision by the director may be appealed to superior court.

The grantee of any permit shall comply with all of the requirements within the small cell permit.

Construction of the small cell facility must be completed within 12 months after the approval date by the city. The grantee may request one extension, to be limited to six months, if the applicant cannot construct the small cell facility within the original 12-month period.

Within 30 days after construction of the small cell facility, the grantee shall provide the city with as-builts of the small cell facilities demonstrating compliance with the permit and site photographs.

The grantee shall commence operation of the small cell facility no later than three months after installation, which may be extended for an additional three months upon the applicant's request for additional time due to matters beyond its reasonable control.

The grantee must maintain the small cell facilities in safe and working condition. The grantee shall be responsible for the removal of any graffiti or other vandalism and shall keep the site neat and orderly, including but not limited to following any maintenance or modifications on the site.

Modification to Small Cell Facilities.

Consolidated Permit.

The utility pole at the proposed location may be replaced with a taller pole for the purpose of accommodating a small cell facility; provided, that the replacement pole shall not exceed a height that is a maximum of 10 feet taller than the existing pole, unless a further height increase is required and confirmed in writing by the pole owner, and that such height extension is the minimum extension possible to provide sufficient separation and/or clearance from electrical and wireline facilities. Replacement wooden utility poles may either match the approximate color and materials of the replaced pole or shall be the standard new wooden utility pole used by the pole owner in the city.

A pole extender may be used instead of replacing an existing pole, but may not increase the height of the existing pole by more than 10 feet, unless a further height increase is required and confirmed in writing by the pole owner and such height increase is the minimum extension possible to provide sufficient separation and/or clearance from electrical and wireline facilities. The pole extender shall be painted to approximately match the color of the pole and shall substantially match the diameter of the pole measured at the top of the pole. A "pole extender" as used herein is an object affixed between the utility pole and the antenna for the purpose of increasing the height of the antenna above the pole.

Antennas, equipment enclosures, and all ancillary equipment, boxes and conduit shall be colored or painted to match the approximate color of the surface of the utility pole on which they are attached.

Multiple antennas are permitted on a utility pole; provided, that each antenna enclosure shall not be more than three cubic feet in volume, with a cumulative total antenna volume not to exceed 12 cubic feet. Antennas should be placed in an effort to minimize visual clutter and obtrusiveness.

Panel antennas shall not be mounted more than 12 inches from the surface of the utility pole.

A canister antenna may be mounted on top of a utility pole, which may not exceed the height requirements described in subsection (6)(a) of this section. A canister antenna mounted on the top of a utility pole shall not exceed the diameter of the pole by more than 12 inches, measured at the top of the pole, and shall be colored or painted to match the pole. The canister antenna must be placed to look as if it is an extension of the pole. In the alternative, the applicant may install a side-mounted canister antenna, so long as the inside edge of the antenna is no more than 12 inches from the surface of the utility pole. All cables shall be concealed either within the canister antenna or within a sleeve between the antenna and the utility pole.

An omnidirectional antenna may be mounted on the top of an existing utility pole, provided such antenna is no more than four feet in height and is mounted directly on the top of a pole or attached to a sleeve made to look like the exterior of the pole, as close to the top of the pole as technically feasible. All cables shall be concealed within the sleeve between the bottom of the antenna and the mounting bracket.

All related equipment, including but not limited to ancillary equipment, radios, cables, associated shrouding, microwaves, and conduit which are mounted on utility poles shall not be mounted more than six inches from the surface of the pole, unless a further distance is technically required, and is confirmed in writing by the pole owner.

Equipment for small cell facilities must be attached to the utility pole, unless otherwise permitted to be ground-mounted pursuant to subsection (9)(a) of this section. The equipment must be placed in the smallest enclosure possible for the intended purpose. The equipment enclosure and all other wireless equipment associated with the utility pole (including but not limited to any conduit, disconnect switches and meters), including wireless equipment associated with the antenna and any preexisting associated equipment on the pole, may not exceed 28 cubic feet. Multiple equipment enclosures may be acceptable if designed to more closely integrate with the pole design and all associated equipment does not cumulatively exceed 28 cubic feet. The applicant is encouraged to place the equipment enclosure behind road signs that may be on the pole, if such road signs are allowed by the pole owner and city code; provided, that such location does not interfere with the operation of the road signs or the small cell facility.

An applicant who desires to enclose both its antennas and equipment within one unified enclosure may do so; provided, that such enclosure is the minimum size necessary for its intended purpose and the enclosure and all other wireless equipment associated with the pole (including but not limited to any conduit, disconnect switches and meters), including wireless equipment associated with the antenna and any preexisting associated equipment on the pole, does not exceed 28 cubic feet. The unified enclosure may not be placed more than six inches from the surface of the pole, unless a further distance is required and confirmed in writing by the pole owner. To the extent possible, the unified enclosure shall be placed so as to appear as an integrated part of the pole or behind road signs; provided, that such location does not interfere with the operation of the road signs or the small cell facility.

Any equipment or antenna enclosures must meet WSDOT height clearance requirements.

The visual effect of the small cell facility on all other aspects of the appearance of the utility pole shall be minimized to the greatest extent possible.

The use of the utility pole for the siting of a small cell facility shall be considered secondary to the primary function of the utility pole. If the primary function of a utility pole serving as the host site for a small cell facility becomes unnecessary, the utility pole shall not be retained for the sole purpose of accommodating the small cell facility and the small cell facility and all associated equipment shall be removed.

All cables and wires shall be routed through conduit along the outside of the pole. The outside conduit shall be colored or painted to match the pole. The number of conduits shall be minimized to the number technically necessary to accommodate the small cell.

The diameter of a replacement pole shall comply with the city's setback and sidewalk clearance requirements and shall not be more than a 25 percent increase of the existing utility pole measured at the base of the pole.

Glulam poles are specifically prohibited.

There is no co-location requirement for small cell facilities located on utility poles.

Antennas and the associated equipment enclosures shall be fully concealed within the pole, unless such concealment is otherwise technically infeasible or is incompatible with the pole design; then the antennas and associated equipment enclosures must be camouflaged to appear as an integral part of the pole or flush-mounted (no more than six inches off the pole) to the pole in a manner that integrates the equipment enclosure into the design of the pole and minimizes clutter and visual impact. If the equipment enclosure is permitted on the exterior of the pole, the applicant is encouraged to place the equipment enclosure behind any road signs that may be on the pole; provided, that such location does not interfere with the visibility of the signs or the operation of the small cell facility. For purposes of this section, "incompatible with the pole design" may include a demonstration by the applicant that the visual impact to the pole or the streetscape would be reduced by placing the antennas and equipment exterior to the pole.

All conduit, cables, wires and fiber must be routed internally in the light pole. Full concealment of all conduit, cables, wires and fiber is required within mounting brackets, shrouds, canisters or sleeves if attaching to exterior antennas or equipment.

Any replacement pole shall substantially conform to the design of the pole it is replacing or the neighboring pole design standards utilized within the contiguous right-of-way.

The height of any replacement pole may not extend more than 10 feet above the height of the existing pole.

The diameter of a replacement pole shall comply with the city's setback and sidewalk clearance requirements, shall not be more than a 25 percent increase in the diameter of the existing pole measured at the base of the pole, and shall comply with the requirements in subsection (9)(e) of this section.

An antenna on top of an existing pole may not extend more than six feet above the height of the existing pole and the diameter may not exceed the diameter of the pole by more than 12 inches, measured at the top of the pole, unless the applicant can demonstrate that more space is needed. The antenna shall be integrated into the pole design so that it appears as a continuation of the original pole, including colored or painted to match the pole, and shall be shrouded or screened to blend with the pole, except for canister antennas which shall not require screening. All cabling and mounting hardware/brackets from the bottom of the antenna to the top of the pole shall be fully concealed and integrated with the pole.

Any equipment or antenna enclosures must meet WSDOT height clearance requirements.

The use of the light pole for the siting of a small cell facility shall be considered secondary to the primary function of the light pole. If the primary function of a light pole serving as the host site for a small cell facility becomes unnecessary, the light pole shall not be retained for the sole purpose of accommodating the small cell facility and the small cell facility and all associated equipment shall be removed.

Small cell facilities may be mounted to the sides of a building if the antennas do not interrupt the building's architectural theme.

The interruption of architectural lines or horizontal or vertical reveals is discouraged.

New architectural features such as columns, pilasters, corbels, or other ornamentation that conceal antennas may be used if they complement the architecture of the existing building.

Small cells shall utilize the smallest mounting brackets necessary in order to provide the smallest offset from the building.

Skirts or shrouds shall be utilized on the sides and bottoms of antennas in order to conceal mounting hardware, create a cleaner appearance, and minimize the visual impact of the antennas. Exposed cabling/wiring is prohibited.

Small cell facilities shall be painted and textured to match the adjacent building surfaces.

Ground-mounted equipment in the rights-of-way is prohibited, unless such facilities are placed underground or the applicant can demonstrate that pole-mounted or undergrounded equipment is technically infeasible. If the applicant builds an underground vault it should design such vault to allow for co-location of additional equipment. If ground-mounted equipment is necessary, then the applicant shall submit a concealment element design, as described in subsection (10)(c) of this section. Generators located in the rights-of-way are prohibited.

No equipment shall be operated so as to produce noise in violation of Chapter 6.16 PMC (Noise Control).

Small cell facilities are not permitted on traffic signal poles.

Small cell facilities are not permitted on ornamental poles, which are described in the City Standards for Public Works Engineering and Construction Manual.

Replacement poles and new poles shall comply with the Americans with Disabilities Act (ADA), city construction and sidewalk clearance standards, and state and federal regulations in order to provide a clear and safe passage within the rights-of-way.

Replacement poles shall be located as near as possible to the existing pole with the requirement to remove the abandoned pole.

The design approved in a small cell permit shall be considered concealment elements and such facilities may only be expanded upon an eligible facilities request described in this chapter when the modification does not defeat the concealment elements of the small cell facility.

No signage, message or identification other than the manufacturer's identification or identification required by governing law is allowed to be portrayed on any antenna, and any such signage on equipment enclosures shall be of the minimum amount possible to achieve the intended purpose; provided, that signs are permitted as concealment element techniques where appropriate.

Antennas and related equipment shall not be illuminated except for security reasons, required by a federal or state authority, or unless approved as part of a concealment element design, as described in subsection (10)(c) of this section.

Side arm mounts for equipment enclosures are prohibited. Further, antennas placed on side arm mounts must comply with the requirements in subsection (6)(f) of this section, and may not be placed on any preexisting side arm mount that extends over the vehicular portion of the rights-of-way.

Any small cell facility shall be removed by the facility owner or authorized agent within six months of the date it ceases to be operational or if the facility falls into disrepair. "Disrepair," as used in this section, refers to a facility or structure which has become so damaged or deteriorated on account of age, the elements, wear and tear, or other cause that it has become a threat to public safety or would constitute a public nuisance as defined in the Puyallup Municipal Code.

The preferred location of a small cell facility on a pole is the location with the least visible impact.

Antennas, equipment enclosures, and ancillary equipment, conduit and cable shall not dominate the building or pole upon which they are attached.

The city may consider the cumulative visual effects of small cells mounted on poles within the rights-of-way when assessing proposed siting locations so as to not adversely affect the visual character of the city.

Small cell facilities are not permitted on any property containing a residential use in the RS zone.

Small cell facilities may not encroach onto or over private property or property outside of the right-of-way without the property owner's express written consent.

The design standards in this section are intended to be used solely for the purpose of concealment and siting. Nothing herein shall be interpreted or applied in a manner which dictates the use of a particular technology, nor prohibits or has the effect of prohibiting the provision of personal wireless services.

New poles within the rights-of-way are only permitted if the applicant can establish that:

An application for a new pole in the right-of-way is subject to administrative conditional use permit review pursuant to Chapter 20.81 PMC.

The concealment element design shall include the design of the screening, fencing or other concealment technology for a tower, pole, or equipment structure, and all related transmission equipment or facilities associated with the proposed wireless communications facility, including but not limited to fiber and power connections.

Even if an alternative location is established pursuant to subsection (10)(a)(i) of this section, the director may determine, pursuant to an administrative conditional use permit, that a new pole in the right-of-way is in fact a superior alternative based on the impact to the city, the concealment element design, the city's comprehensive plan and the added benefits to the community.

Prior to the issuance of a permit to construct a new pole or ground-mounted equipment in the right-of-way, the applicant must obtain a site-specific agreement from the city to locate such new pole or ground-mounted equipment. This requirement also applies to replacement poles when the replacement is necessary for the installation or attachment of small cell facilities, the replacement structure is higher than the replaced structure, and the overall height of the replacement structure and the small cell facility is more than 60 feet.